Buke motor - installation method of frameless motor

The servo motor can control the speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. The rotor speed of the servo motor is controlled by the input signal, and can respond quickly, in the automatic control system, used as an actuator, and has an electromechanical time constant...

(1) Encoder failure: It refers to the failure of the components of the encoder itself, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. (2) Encoder connection cable failure: the probability of this fault is the highest, and the maintenance ...

A stepper motor driver is an actuator that converts electrical impulses into angular displacement. When the stepper driver receives a pulse signal, it drives the stepper motor to roll a fixed viewpoint (called the "step angle") in the set direction.

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

(1) Accurate detection device: to form a closed-loop control of speed and position. (2) There are a variety of feedback comparison principles and methods: according to the principle of information feedback realized by the detection device, the feedback comparison method of the servo system is also different. At present, the commonly used pulse comparison, phase ratio ...

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

One. SERVO MOTOR DIMENSIONS: 38MM, 58MM, 66MM, 80MM.100MM. Two. Servo motor encoders are divided into: singleturn, multiturn. Three. Servo motor encoders are divided into magnetic absolute encoders and photoelectric absolute encoders according to the principle Four. Servo motor ...

1. If the servo motor is an AC motor, it is a DC inverter air conditioner for speed regulation; If the servo motor is a DC brushless DC motor, it is the DC power supply DC transformer speed regulation; All servo motors can be used as "PLC motor speed regulating power supply circuit servo motor". 2、 ...

1. The power of the motor 2. The power supply voltage of the motor 3. The encoder type of the motor 4. The size of the base of the motor 5. The movement mode of the motor 6. Motor communication bus 7. Whether the motor is equipped with a brake mechanism 8. Motor driver class ...

Daily maintenance of the touch screen: 1. The capacitive touch screen should generally be filmed, and it should be pasted well. membranes (double-layer membranes) that meet ESD standards; 2. The capacitive touch screen is cleaned regularly, and the liquid crystal cleaning solution used for the computer is used (alcohol and furniture cleaning liquid cannot be used); 3. Transport...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

1. AC motors are cheaper to manufacture. 2. With the development of vector frequency conversion technology, it has been possible to simulate direct current with frequency conversion motors 3. Compared with DC motor, it has enough advantages in simple structure, easy maintenance, low environmental requirements, energy saving and improved productivity.

Advantages and disadvantages of DC servo motors Advantages: accurate speed control, torque speed characteristics are very hard, simple control principle, easy to use, cheap price. Disadvantages: brush commutation, speed limit, additional resistance, occurrence of wear particles (not suitable for dust-free and explosive environments). Straight...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

Frameless torque motor is a new type of direct-drive torque motor, which is designed for applications that require small size, light weight, low inertia, low cogging torque, and high power. High reliability - no mechanical transmission, long life and easy installation. Serialized products are not limited to the following types ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

1. a frame The frame structure varies depending on the motor cooling method, protection type, installation method, and purpose. According to its material classification, there are several types of cast iron, cast aluminum and steel plate structures. Cast iron frame with ribs. The base is connected to the end cap and fastened with bolts. Cast aluminum machine base generally does not have ...

1:11 alarm, control the power supply undervoltage, control the power inverter on P. The voltage between N is lower than the specified value. There are defects in the internal circuitry of the driver, etc. 2:12 alarm, control power supply overvoltage, control power inverter on P. N voltage exceeds the specified value, ...