The Rosemount 3051 transmitter will not be powered on or may damage the transmitter after it is placed in the tripping device. When our technicians have understood these problems, they have analyzed and made corresponding countermeasures from three aspects, as follows:
Analysis and countermeasures for the Rosemount transmitter when it is unable to be powered on.
1. There is something wrong with the leakage circuit breaker itself
When the jump bar indicator and power indicator are not on, it is necessary to check whether the fuse is blown; whether the transformer, voltage regulator manifold, and power switch are damaged; Whether the power supply of the leakage protector is normal. The solution is to use the multimeter 500V voltage block to measure the power supply voltage of the leakage protector, if the voltage is normal, you can use the power failure to separate the power switch, internal connection line, fuse and transformer, and replace the damaged or repaired components after finding the fault; If the voltage is very low or there is no voltage, check the wiring to solve the problem.
2. Contactor fault
If the Rosemount transmitter shows problems such as coil burning, poor contact at the joint, etc., the corresponding treatment method is: replace the coil, tighten the screws or weld the joint, use the 500V voltage block live measurement or use a multimeter ohm to measure the voltage at both ends of the coil, determine whether the coil is open, and then check whether the moving iron core has any jamming phenomenon.
3. The pressure transmitter is not equipped with a leakage circuit breaker and the circuit of the device leakage circuit breaker is electrically connected
Find out whether the indicator lights, lights, temporary lights, appearances and other electricity on the distribution board or control cabinet are connected on both sides of the zero sequence current transformer, adjust the wiring, and the wiring of the same load should be connected in front of or behind the unified zero sequence current transformer.
|
More on that
|
What is the difference between a Siemens transmitter and a Rosemount transmitter
Differences between Siemens transmitters and Rosemount transmitters: Siemens' transmitters are piezoresistive pressure transmitters, while Rosemount's transmitters are capacitive pressure transmitters.
The transmitter converts the output signal of the sensor into other signals that can be recognized by the controller.
|
|
What factors affect the performance of the Rosemount 3051 differential pressure transmitter?
1. Effect of temperature
Rosemount differential pressure transmitters will vary greatly in process temperature, ambient temperature, and will certainly differ from the reference conditions when the transmitter is tested, which also means that the functionality will be different from the reference accuracy presented. Temperature on differential pressure transmitters ...
|
|
External factors influencing the failure of the Rosemount 3051 transmitter
1. The impulse tube is faulty
There are two simplest problems with the pressure duct of the Rosemount 3051 transmitter, which is blockage and leakage of the pressure duct. Once this problem is presented, the most obvious manifestation is that the leakage surface index of the impulse pipe will be abnormal.
|
|
How the Rosemount transmitter is wired
During the use of the Rosemount transmitter, wire the Rosemount transmitter according to the following steps:
1. Take out the Rosemount 3051 and remove the electronic enclosure marked "FIELD TERMINALS".
2. Will be positive ...
|
|
How Rosemount Electromagnetic Flowmeters Troubleshoot Air Ducts
Rosemount Electromagnetic Flowmeter Eliminates Empty Pipe ProblemRosemount Electromagnetic Flowmeter Eliminates Empty Pipe Problem
If the ATC detection is unexpected, the following measures can be adopted:
1. Make sure the sensor is overflowing.
2. Ensure that the measuring electrode has not been installed on the top of the pipe of the sensor.
...
|
|
What to do if the Rosemount pressure transmitter measurement is inaccurate
Common Rosemount pressure transmitter measurement incorrect situations:
1. The input impedance of the Rosemount transmitter load should be in line with RL≤ (transmitter supply voltage -12V)/(0.02A)Ω if necessary, if it does not match, corresponding measures can be adopted according to its differences: such as increasing the power supply ...
|
|
The difference between a Rosemount transmitter and a Siemens transmitter
The difference between Siemens' transmitter and Rosemount's transmitter: Siemens' transmitter is a piezoresistive pressure transmitter, and Rosemount's transmitter is a capacitive pressure transmitter.
The transmitter converts the output signal of the sensor into a signal that can be recognized by the controller.
|
|
Rosemount transmitter signal line grounding method
If the Rosemount transmitter does not have alarms and safety adjustment options installed, the transmitter will typically operate according to the default alarm settings, i.e., the alarm condition is set to "high" and the safety is set to "off". Then proceed as follows:
1. ...
|
|
That's how Rosemount transmitters should be selected
Rosemount transmitter selection requires a good transmitter before use, so its selection is very important
1. According to the pressure interface mode
Generally, threaded connection is the standard interface method.
2. According to the required accuracy level
Measurement error of the transmitter ...
|
|
Types of Rosemount transmitters
The intelligent Rosemount transmitter is also equipped with a hand-held terminal (external data setter or grouper) for setting the transmitter parameters, such as setting the type of transmitter, range adjustment, zero point adjustment, input signal selection, output signal selection, engineering unit selection and damping time constant.
|
|
Factors to consider when installing a Rosemount 644 temperature transmitter
Rosemount 644 temperature transmitter must be considered when installing the factors, only we solve these unfavorable factors, in the installation of the Rosemount temperature transmitter will not encounter some unnecessary things
routine
Electrical temperatures such as RTDs and thermocouples ...
|
|
What causes inaccurate measurements in Rosemount pressure transmitters
Rosemount Pressure Transmitter Inaccurate Measurement Causes:
1. Whether the power supply of the Rosemount pressure transmitter is normal, if it is less than 12VDC, you should check whether there is a large load in the circuit, and the input impedance of the transmitter load should be in line with RL≤ (transmitter supply voltage -12V)/(0.02A...
|
|
How the Rosemount 3051 pressure transmitter works
The 3051 pressure transmitter is used to measure the level, density, and pressure of liquids, gases, or vapors, and then convert the pressure signal into a 4-20mADC signal output. There are mainly capacitive pressure transmitters and diffusion silicon pressure transmitters, ceramic pressure transmitters, strain gauge pressure transmitters, etc.
...
|
|
Problems to be noted when calibrating Rosemount transmitters
1. After adjusting the zero point, use the standard pressure source to apply pressure slowly, and increase the pressure to the maximum scale, and the output value is about 20mA.
2. The verification regulations require that the two high and low pressure chambers of H and L are connected to the outside world, and observe that the zero position is not in the direction of 4mA.
|
|
How to maintain the United States rosemount3051 pressure transmitter
Rosemount pressure transmitters often have some common faults in the whole process of accurate measurement, and the immediate judgment and resolution of common faults is especially important for the manufacturing that has been carried out. According to the work experience in the usual maintenance, people have summarized and sorted out some ...
|
|
Pipe diameter requirements for the installation of the Rosemount 8800D vortex flowmeter
1. The upstream and downstream pipe diameter of the flowmeter on the installation point must be installed in accordance with the standard flowmeter caliber, otherwise the measurement accuracy will be affected.
2. If there is a tapering pipe in the upstream of the flowmeter installation point, there should be a straight pipe section of equal diameter of not less than 15D (D is the diameter of the pipe) in the upstream of the flowmeter, and there should be ...
|
|
The Rosemount Twisted Square thermowell avoids wake shedding
When a problem arises in the design of Rosemount thermowells, it is necessary to analyze the cause of its failure, and then go further and propose solutions. In some less complicated cases, it may be necessary to make a small change, such as adding one millimeter without changing the predetermined measurement orientation ...
|
|
Rosemount Pressure Transmitter Measurement Principle
The Rosemount pressure transmitter measurement principle progresses as follows:
1. The pressure transmitter transmits the pressure on the high and low pressure sides to the movable (sensing) diaphragm in the center of the sensor through silicone oil.
2. The movable diaphragm undergoes a slight displacement under the effect of differential pressure, so that the movable (sensing) membrane ...
|
|
Factors to consider for Rosemount 5300 Series Radar Level Gauge Interface Measurements
For applications where the waveguide is completely submerged in liquids, the Rosemount 5301 measurement interface can be used, but the following guidelines should be followed
1. The dielectric constant of the above product must be known and cannot be changed. The Radar Master software has built-in dielectric constant calculations ...
|
|
How to maintain the Rosemount 3051 pressure transmitter
United States rosemount 3051 pressure transmitter maintenance is mainly divided into two points:
1. In the whole process of accurate measurement, some common faults often occur in the Rosemount pressure transmitter, and the immediate judgment and analysis and resolution of common faults are especially important for the production and manufacturing that has been carried out.
|
|
Contact
working hours
