1. If the electronic ruler has been used for a long time, and the seal is now aged, and there are many impurities mixed with it, and the water mixture and oil will seriously affect the contact resistance of the brush, which will make the displayed numbers keep jumping. At this time, it can be said that the electronic ruler of the linear displacement sensor is now damaged and needs to be replaced.
2. If the capacity of the power supply is very small, there will be many situations, so the power supply needs to have sufficient capacity. Then, if the capacity is insufficient, the following situation will be formed: the movement of the melt will change the appearance of the clamping electronic ruler and wave, and perhaps the movement of the clamping will shake the appearance of the injection electronic ruler, and the measurement result will be very wrong. If the driving power supply of the solenoid valve is at the same time as the power supply of the linear displacement sensor, it is easier to present the above situation, and the voltage level of the multimeter can even measure the relevant fluctuation of the voltage when the situation is serious. If the condition is not due to high-frequency disturbance, electrostatic disturbance, or the neutral is not good enough, then it may be caused by the power of the power supply is too small.
3. Frequency modulation disturbance and electrostatic disturbance may make the display digital jump of the electronic ruler of the linear displacement sensor. The signal line of the electronic ruler should be separated from the strong current line of the equipment. The enclosure of the enclosure must be mandatory, and at the same time, the enclosure of the enclosure must be in excellent contact with the ground. The signal line needs to use a shielded wire, and a section of the electrical box should be grounded with the shielded wire. If there is a high-frequency disturbance, the voltage measurement of the multimeter will usually appear normal, but the displayed number will not stop; In the case of electrostatic disturbance, the situation is the same as that of high-frequency disturbance. To prove whether it is static disturbance, you can first use a section of power cord to connect the cover screw of the electronic ruler with some metal on the machine. However, if you want to eliminate high-frequency disturbance, it is difficult to use the above method, and the frequency converter saver and the manipulator often present high-frequency disturbance, so you can try to use the method of aborting the high-frequency economizer or manipulator to verify whether it is high-frequency disturbance.
4. If the electronic ruler of the linear displacement sensor is next to the process of operation, and the display data at a certain point beats regularly, perhaps when there is no display data, it is necessary to check whether the insulation of the connecting wire is damaged, and the short circuit to the ground caused by regular contact with the shell of the machine.
5. The voltage of the power supply must be stable, and the voltage demand of the industry meets the stability of ±0.1[%], for example, if the reference voltage is 10V, it can be allowed to have a ± 0.01V fluctuation change, if not, it will cause the situation of the apparent scam shaking. However, if the fluctuations of the appearance of the shaking at this time do not exceed the fluctuations of the shaking voltage, then the electronic ruler is normal.
6. At the edge of the connection process, we must pay more attention to the fact that the three wires of the electronic ruler cannot be connected wrongly, and the power line and output line cannot be replaced. If the above line is connected incorrectly, there will be a large linear error, it is difficult to control, the accuracy of the control will become very poor, and the appearance is very simple, and the phenomenon of beating is very simple.
|
More on that
|
How to choose a pressure sensor – we are blessed
1. Recognize the type of pressure measurement, that is, to measure the gauge pressure, absolute pressure or differential pressure. Gauge pressure refers to the pressure value with atmospheric pressure as the zero point, which can have positive and negative values, positive above atmospheric pressure, and negative below atmospheric pressure. The absolute difference refers to the pressure value with the vacuum as the zero point, and the absolute pressure is as long as the value is positive ...
|
|
The application of P+F sensors
Positioning, Navigation, Sorting...... The completion of various functions of mobile robots can be said to be inseparable from the role of sensors, and with the continuous expansion of the scope of use of mobile robots, the environment they face is more complex and diverse, and the requirements for sensors are also constantly improving.
...
|
|
Selection criteria for proximity switches
Points to note in the selection of proximity switches
1. The working voltage of the proximity switch output is selected, generally DC type DC24V or AC AC250V optional;
2. Proximity switch output method selection, generally NPN-normally open, NPN-...
|
|
Safety barriers are used for intrinsically safe system features
The barrier and barrier are composed of four parts: the input signal processing unit, the barrier unit, the output signal processing unit, and the power supply. Depending on the direction of the signal, a substantial safety plan is added to the input or output unit, which then forms a barrier and a barrier. Traditional barrier and safety ...
|
|
Important things to do with your torque sensor – we are blessed
In the process of application, the sensor will inevitably be affected by the environment, temperature, dust and other factors, so that the equipment is aging or wearing, and if these problems are not dealt with in time, it will bury potential troubles for the future use of the equipment, resulting in large and small problems, and ...
|
|
Features of the isolated safety barrier
The isolated barrier can be adapted for PCL applications. If the working environment of the field equipment is relatively bad, resulting in the signal sensing line of the PLC breaking the skin and connecting with other lines of different voltages or shorting to the equipment at the same time, there will be strong electricity into the pIc input port, which will cause the whole module to be burned, resulting in ...
|
|
The difference between sensors and transmitters – we are blessed
Sensors and transmitters are thermal surface concepts. A sensor is a general term for a device or equipment that can be measured by rules and converted into a usable output signal according to a certain rule, which is generally composed of an active element and a conversion element. When the output of the sensor is a regular canonical signal, then ...
|
|
Introducing the sensor
From leveling cranes and monitoring the inclination of front-end loaders to operating elevators, inclination and acceleration sensors can be used in a variety of ways. These sensors are guaranteed to measure even in harsh conditions. Thanks to the innovative split unit concept, the F99 series ...
|
|
Sensor Selection Considerations – Benefit Us
In order to carry out a detailed measurement operation, it is necessary to first consider the principle of the sensor, which needs to be determined after analyzing many factors. Since, even if the same physical quantity is measured, there are multiple principles of sensors to choose from, which principle of sensor is more suitable, ...
|
|
The key factor influencing sensor performance – the company
Because the metal material is used as the elastomer of the load cell load cell, when the fine particles between the external force and the micro-strain disappear, the micro-strain disappears, but whether it can be fully recovered to the original non-stress state will be changed according to the metal data of the elastomer.
...
|
|
Common dry contact signals for safety barriers
The dry contact of the barrier is an electrical switch that has two positions: closed and disconnected. There is no polarity between the two contacts of the dry contact and is interchangeable. That is, a simple switch, the contact does not provide power supply, and the power supply can be used to control the condition of the equipment. But it doesn't offer ...
|
|
The RHI90 series encoders have been fully upgraded
The new RHI90 series encoders offer significant improvements in electrical and mechanical performance
With the extensive use of electronic components and equipment in the field of automation, the risks of malfunction and damage caused by electrical and electromagnetic disturbances are also invisible.
|
|
Wiring of weighing strain gauge tension and compression sensors – we are in control
Wiring method of weighing strain tension and compression sensor:
Strain gauge tension and compression load cells can be wired in two different input and output wiring methods:
The first is the four-wire connection method.
The load cell of the four-wire connection method has no special requirements for the secondary instrument panel, and it is very convenient to use.
|
|
The difference between a force transducer and a load cell – we are blessed
A device that converts the value of a force transducer into an associated electrical signal. Force is the direct cause of changes in the motion of materials. Force sensors can detect tension, tension, pressure, components, torque, internal stresses, and strains. The specific equipment is metal strain gauges, pressure sensors, etc., which have become electric ...
|
|
Pressure control of servo presses – we are blessed
The servo press drives the fine ball shaft through the synchronous belt to complete the accurate orientation control of the pressure spindle, and the high-sensitivity pressure sensor equipment is at the front end of the pressure spindle, which can detect the load of the pressure spindle in real time. Real-time collection of orientation and load data to complete the fine ...
|
|
Pressure Transmitter Verification Regulations
A pressure transmitter is a type of instrument that converts a pressure variable into a consistent output signal that can be transmitted, and there is a given continuous function relationship between the output signal and the pressure variable, which is generally a linear function. Pressure variables include positive and negative pressure, differential pressure and pressure. Pressure transmitters are available in electric and ...
|
|
The sensitive core structure of the accelerometer – we are blessed
The accelerometer is a sensor that can measure acceleration, this sensor can help the product to understand the environment in time, and it is very accurate, so what is the structure of its sensitive core?
1. Compression method: ...
|
|
Troubleshooting for coding problems
P+F encoders are devices that compile signals (e.g. bit streams) or data and convert them into signals that can be communicated, transmitted, and stored. The P+F encoder converts angular or linear displacements, the former known as the code disc and the latter into an electrical signal. Therefore, the phenomenon: 1, ...
|
|
How to identify the number of pulse positions in an encoder – we are blessed
The pulse encoder is a rotary encoder that uses the rotation pulse for signal output, and the main characteristics are the standard shape and diversified shape structure; The internal coding is stable, the signal output qiang, and the pulse value and positioning value are clear. Therefore, when choosing this type of punching encoder, ...
|
|
Factors influencing the measurement accuracy of ultrasonic sensors - Doublebless
Sensors are used for a variety of measurements, but the difference in measurement accuracy has a great impact on the user, so what are the main factors that affect the measurement accuracy?
Measurement accuracy ...
|
|
Contact
working hours
