The sensitive core structure of the accelerometer – we are blessed

The first is pressure, and the transmitter can't afford to lose it. In this case, see if the pressure connector is leaking or clogged, if you admit that it is not, look at the wiring method and see if the power supply is normal, simple pressure to confirm if the output has changed, or if there is an output at the zero point of the sensor ...

1. Each electrical interface has its own characteristics, but also has different baud rate and transmission interval, which can be selected according to the specific application environment of the site, and the actual transmission interval is very related to the transmission rate, encoder and communication cable installation disturbance environment, grounding, cable material selection, etc. ...

Pressure: The force acting vertically and evenly over a unit area. In physics, this is called "pressure". Range: i.e. the scale of pressure. Refers to the use of sensors to measure the amount of pressure. Medium: refers to the object to be measured. Generally steam, water, oil, acid, alkali or mixture. Precision...

1. The safety barrier should be installed in a safe place, and the environmental conditions meet the requirements of the "application conditions" in the "Safety Gate Selection Sample". 2. The connecting wires of the intrinsically safe end (blue end) and non-intrinsically safe end circuits of the barrier safety barrier should be laid separately in the wiring slot.

An encoder is a device that compiles or converts signals or data into signals that can be communicated, transmitted and stored – encoders can be divided into two categories: incremental and absolute. Incremental encoders are the most important way to convert bits ...

1. The safety barrier should be installed in a safe place, and the environmental conditions meet the requirements of "application conditions" in the "Safety Barrier Selection Sample". 2. The connecting wires of the intrinsically safe end (blue end) and non-intrinsically safe end circuits of the barrier safety barrier should be laid separately in the wiring slot.

The dynamic characteristics of a sensor refer to the characteristics of the output of the sensor when the input changes. In practice, the dynamic characteristics of the sensor are often indicated by its echo to some normative input signals, because the echo of the sensor to the normative input signal is easy to obtain by experimental methods, ...

Whether it is a linear displacement sensor or a rope displacement sensor, it often encounters a variety of problems when it is used, including quality problems, application problems, environmental problems, etc., but the use of problems is common, and improper use is easy to damage the sensor. ...

The premise of load cell replacement is that the axis of the applied force coincides with the axis of the sensor, we should know one thing, that is, with the increase of the additional load, the microvolt/indexing signal output by the sensor decreases. About the electromechanical junction of the S-shaped sensor installed in the second force transmission link ...

There are not many single ferrule terminal joints on the market now, and most manufacturers are using double ferrule terminal joints, and the market price is about 9-18 yuan, and the price is different according to different types. Fittings, whether double ferrule end fittings or single ferrule end fittings, are all selected.

In many applications, there are certain safety requirements not only for the sensors in use, but also for the sensor cables. In order to ensure that the adapter components also meet these requirements, the new cable maintenance system provides the ambition for sensor adapters, cable conduits and cable glands ...

The inlet pressure sensor is abbreviated as MAP. It connects the intake manifold with a vacuum tube, and induces the vacuum change in the intake manifold with the different speed loads of the engine, and then converts the change of internal resistance from the sensor into a voltage signal, which is used by the ECU computer to correct the fuel injection amount and ignition timing angle. Other words...

Eltra incremental encoders fall into three categories: Optical solid shaft incremental encoder Eltra. The couplings in these types are made of solid shafts. · EL-ER 30 E/H； · EH 38 A/B/D； · EL-E ...

1. Test for NPN output sensor The NPN sensor output, also known as OC gate output, is based on the principle of open collector output of a transistor. The principle of NPN type OC gate output is whether the output of the NPN transistor and GND are short-circuited. When the control is active, the transistor is turned on, the output and the GND ...

There are great differences in the skills, design, function and adaptability of pressure sensors, as well as the conditions and price of pressure sensors. According to preliminary estimates, there are more than 60 types of pressure sensors in the world and at least 300 companies produce pressure sensors. ...

The isolated barrier can be adapted for PCL applications. If the working environment of the field equipment is relatively bad, resulting in the signal sensing line of the PLC breaking the skin and connecting with other lines of different voltages or shorting to the equipment at the same time, there will be strong electricity into the pIc input port, which will cause the whole module to be burned, resulting in ...

1. The linear displacement sensor should be used to prevent over-travel in the application, and a certain margin should be left in the selection to facilitate the use of the device. 2. The linear displacement sensor device is fixed by a bracket, and then the follow-up shaft is connected to the moving object to be measured. When the sensor is fixed in the device, it can be ...

Sensor calibration refers to the process of transmitting the standard value expressed by the norm to the indexing of the sensor's operating range, and the indexing is determined. The calibration of the sensor is based on the standard value generated by a standard device (e.g. a known standard force, pressure, torque, displacement, etc.).

Proximity sensors are a general term for sensors that replace contact detection methods such as limit switches and do not require contact detection of the detected object. It is capable of converting information about the motion and presence of objects into electrical signals. The detection method of replacing the electrical signal includes: using an electromagnetic induction bow to ...

1. Recognize the type of pressure measurement, that is, to measure the gauge pressure, absolute pressure or differential pressure. Gauge pressure refers to the pressure value with atmospheric pressure as the zero point, which can have positive and negative values, positive above atmospheric pressure, and negative below atmospheric pressure. The absolute difference refers to the pressure value with the vacuum as the zero point, and the absolute pressure is as long as the value is positive ...