Classification and characteristics of the human-machine interface of Buke

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

In terms of the response speed of the servo drive: the torque mode has the smallest amount of calculation, and the driver responds the fastest to the control signal; The position mode is the most computationally intensive, and the driver is the slowest to respond to the control signal. When there are relatively high requirements for dynamic performance in motion, it is necessary to ...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

In the past industrial field, HMI touch screens were used more as a window for people to interact with mechanical equipment, and were used to connect various PLCs and sensors. Nowadays, in the context of the Industrial Internet of Things, manufacturing enterprises need to integrate OT and IT technologies more to achieve their own digital and intelligent transformation.

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

Buke MK series all-in-one machine on the market for more than a year, received unanimous praise from many customers, in the Buke "quality first" to create an end-to-end full life cycle product quality management system" and "demand management" under the internal and external drive, through the application feedback of this series of products and in order to fit more ...

1. High efficiency Due to its unique speed-torque capability, AC motors offer the highest efficiency for many applications, which allows them to run a wide range of applications while minimizing heat, wear, or degradation. Therefore, AC motors are often used to form large ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

The servo motor can control the speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. The rotor speed of the servo motor is controlled by the input signal, and can respond quickly, in the automatic control system, used as an actuator, and has an electromechanical time constant...

1. In the daily inspection, the lubrication system, appearance, temperature, noise, vibration and abnormal phenomena are mainly checked, and the ventilation and cooling system, sliding friction and fastening of each component are also checked, and the inspection records are carefully made. 2. During the monthly or regular inspection, the main inspection ...

1. Hydraulic servo control system The hydraulic servo control system is based on the power provided by the motor, and the hydraulic pump is used to convert the mechanical energy into pressure and push the hydraulic oil. By controlling various valves to change the flow direction of the hydraulic oil, so as to push the hydraulic cylinder to make different strokes, different directions of the movement...

One. SERVO MOTOR DIMENSIONS: 38MM, 58MM, 66MM, 80MM.100MM. Two. Servo motor encoders are divided into: singleturn, multiturn. Three. Servo motor encoders are divided into magnetic absolute encoders and photoelectric absolute encoders according to the principle Four. Servo motor ...

What are the main differences between the two? 1. The way of control is different Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. Work ...

1. Position proportional gain Set the proportional gain of the position ring adjuster; The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillation or overshoot; The parameter values are determined by the specific servo system type ...

1. AC motors are cheaper to manufacture. 2. With the development of vector frequency conversion technology, it has been possible to simulate direct current with frequency conversion motors 3. Compared with DC motor, it has enough advantages in simple structure, easy maintenance, low environmental requirements, energy saving and improved productivity.

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...