Analysis of the cause of the fault code 004.0 of the servo drive

First, the common causes of such faults caused by mechanical oscillation (acceleration/deceleration) when the motor is powered on are: (1) The pulse encoder is faulty. At this time, the servo system should be checked to see if it is stable, whether the circuit board maintenance detection current is stable, and at the same time, the electrical ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) Control ...

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

The stepper motor is a discrete motion device, which is intrinsically related to modern digital control technology. In the domestic digital control system, the stepper motor is widely used. With the advent of all-digital AC servo systems, AC servo motors are also increasingly used in digital ...

1. According to the type of working power supply: it can be divided into DC motor and AC motor. 1) DC motors can be divided into brushless DC motors and brushed DC motors according to their structure and working principle. Brushed DC motors can be divided into: permanent magnet DC motors and electromagnetic DC motors.

1. Servo motor encoder is a product installed on the servo motor, which is equivalent to a sensor. 2. Do speed closed-loop and azimuth closed-loop to complete accurate speed regulation and accurate azimuth control. 3. The servo motor has its own encoder, which can be converted into servo electronic gears.

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

1:11 alarm, control the power supply undervoltage, control the power inverter on P. The voltage between N is lower than the specified value. There are defects in the internal circuitry of the driver, etc. 2:12 alarm, control power supply overvoltage, control power inverter on P. N voltage exceeds the specified value, ...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

Buke touch screen programming software is a professional touch screen programming software, support for MT505T, MT506MV, MT508T, MT510T and other models, can assist users in the extreme time to grasp its planning methods, very suitable for modern industry increasingly large workload and function ...

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

1. Please check the motor power line to confirm whether there is a short circuit in the phase wire of the motor 2. If there is no short circuit in the phase line of the motor, it is determined that the internal power tube problem of the driver is determined

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...