Buke servo motor - servo drive repair fault code

1. Hydraulic servo control system The hydraulic servo control system is based on the power provided by the motor, and the hydraulic pump is used to convert the mechanical energy into pressure and push the hydraulic oil. By controlling various valves to change the flow direction of the hydraulic oil, so as to push the hydraulic cylinder to make different strokes, different directions of the movement...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1. Wipe the motor. Remove the dust and sludge on the outside of the motor base in time. If there is a lot of dust in the environment, it is best to clean it once a day. 2. Check and wipe the motor terminals. Check whether the junction box wiring screws are loose or burned. 3. Check the screws of each fixed part ...

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

1. Servo motor pulse control mode In some small stand-alone equipment, the use of pulse control to achieve the positioning of the motor should be the most common application method, this control method is simple and easy to understand. The basic control idea: the total pulse amount determines the motor displacement, and the pulse frequency determines the ...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

6. The motor vibrates greatly during operation (1) The cause of the failure (1) Due to excessive clearance of worn bearings; (2) uneven air gap; (3) Rotor imbalance; (4) Bending of the rotating shaft; (5) The coaxial axis of the coupling (pulley) is too low. (2) Troubleshooting ...

1. Check whether the joints of each connecting line are loose; 2. Check whether there is a conflict between the serial port and the abort number, and if there is a conflict, the resources should be adjusted to circumvent the conflict. Then check whether there are gaps in the surface layer of the human-machine interface, and if there are gaps, they should be replaced immediately. It also needs to be inspected ...

1. Start the servo motor before work (1) Measure the insulation resistance (0.5M or more for low-voltage motors). (2) Measure the power supply voltage, check whether the wiring of the motor is correct, and whether the power supply voltage meets the requirements. (3) Check whether the starting device is normal. ( ...

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

The first type, the split-phase starting type, as shown in Figure 1, is assisted by an auxiliary starting winding, and its starting torque is not large. The operating rate remains roughly constant. It is mainly used in electric fans, air conditioning fans, motors, washing machines and other motors. Second, when the motor is stationary, the centrifugal switch is connected to the ...

1. The first difference between a servo encoder (synchronous service motor) and an ordinary encoder is that it provides sensing signal feedback for the commutation of the starting current. The main performance indicators of servo motor encoders are shift rate, accuracy, and repeatability. 1) Routinely mentioned 17-bit to 25-bit singleturn resolution ...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

On December 10th, the "2020 Buke - IoT Machine Internet of Things Solution Seminar" was held in Wenzhou Ruian, with more than 60 company leaders including Tang Dong, chairman of Buke Co., Ltd., Wang Gang, sales executive, and Ouyang Yunsheng, director of HMI products, attended by more than 60 company leaders, as well as new/old agents and terminals from Wenzhou.

1. Product introduction USING 32-BIT RISC CPU AND A STREAMLINED LINUX KERNEL, THE MT4000 SERIES OF HUMAN-MACHINE INTERFACE PRODUCTS CAN DISPLAY A VARIETY OF TRUE-COLOR GRAPHICS FORMATS, AND ITS OUTSTANDING PROCESSING SPEED AND RICH SOFTWARE FUNCTIONS CAN MEET THE NEEDS OF MOST USERS. Support with the vast majority of PLCs directly ...

1. Servo motor encoder is a product installed on the servo motor, which is equivalent to a sensor. 2. Do speed closed-loop and azimuth closed-loop to complete accurate speed regulation and accurate azimuth control. 3. The servo motor has its own encoder, which can be converted into servo electronic gears.

1. Surface acoustic touch screen. (1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when the position is corrected. Solution 1: Recalibrate ...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

Point 1 When the servo motor jitters at zero speed, the gain should be set high, which can reduce the gain value. If the alarm stops when starting, the most likely is that the phase sequence of the motor is incorrect. Point 2 1. When the PID gain adjustment is too large, it is easy to induce...