Characteristic parameters of the BJ series of Autonex photoelectric sensors

Modular power supplies are power supplies that can be mounted directly on a printed circuit board and feature power supply to application-specific integrated circuits (ASICs), digital signal processors (DSPs), microprocessors, memories, field-programmable gate arrays (FPGAs), and other digital or analog loads.

Key 1: Whether the speed of the motor is normal, whether there is speed jitter and stalled rotation (you can check it with a tachometer). The key is whether the anchor bolts of the motor are loose, whether the root is defective, and whether there are debris around. The key is three, whether the housing and coupling of the motor are defective, ...

Cover the safety light curtain with your hands and observe whether the indicator light conversion is normal. During the use of the punch photoelectric protection device, the orientation of the photoelectric protection device shall not be changed at will. In the protection zone, the light curtain should be blocked by hand, and the machine should be able to stop the operation immediately. ...

1. Observe whether the outside of the load cell is deformed or cracked. If there is any damage, please contact the manufacturer immediately. 2. Find the connection end of the sensor in the weighing controller, and measure the connection circuit of the sensor. The general excitation voltage (between EXC+ and EXC-) is 5-10V, and the output ...

1. Percussion hand pressure method It is common to encounter the phenomenon of good and bad operation of the instrument, and most of this phenomenon is due to poor contact or virtual welding. In this case, percussion and hand pressure can be used. The so-called "percussion" is to ...

1. Avoid strong light sources Photoelectric sensors can generally operate stably when the ambient illumination is high. However, avoid facing the optical axis of the sensor with strong light sources such as sunlight and incandescent lamps. When the angle of the optical axis of the sensor (light receiver) and the strong light source cannot be changed, the sensor can be surrounded by ...

Humidity sensors are divided into resistive and capacitive types, and the basic form of the product is to coat the substrate with moisture-sensitive materials to form a moisture-sensitive film. After the water vapor in the air is adsorbed on the moisture-sensitive material, the impedance and dielectric constant of the element are greatly changed, so as to make a moisture-sensitive element. ...

The pressure sensor in the servo press is built-in, which can ensure that the force on the spindle is not affected by the radial separation force, avoid part of the load in the installation, do not directly connect the workpiece, and is not easy to damage. High-speed rings of ...

Dual PID auto-adjustment function There are high-speed response modes and slow reaction modes in the PID function. When you want to reach the desired value quickly, use the high-speed mode (PIDF mode) When you want to minimize overshoot, use slow mode (PIDS mode) ...

Voltage sensor refers to a sensor that can sense the measured voltage and convert it into a usable output signal, in a variety of detection and control systems, it is often necessary to track and collect the communication DC voltage signal that changes at high speed, and do spectrum analysis on some more complex voltage waveforms. Voltage Sensors ...

Load cells are used to measure weight and can be found everywhere in our daily lives, such as at supermarket counters or on highways. Load cells generally consist of elastomers with strain gauges. Elastomers are generally made of steel or aluminum. It is very robust and has very little elasticity. ...

The BH series photoelectric sensors can be used with M18 fixing nuts and fixing nuts for frontal equipment, or with M3 bolts and nuts for peripheral equipment. Sensitive equipment options promise easy application in a variety of industrial environments. The sensor can be equipped with a simple wire to generate individual or simultaneous N...

1. Check the standard of the equipment hole: Assuming that the standard of the equipment hole is not suitable, some of the threads of the sensor will be slightly worn during the equipment process. This not only affects the sealing performance of the equipment, but also makes the pressure sensor inadequate, and may even cause safety hazards. ...

The SFN series of safety non-touch door switches reliably monitors the opening and closing of dedicated actuator doors by means of magnetic detection. This product can be connected to up to 30 units through a dedicated controller, and it can be used vertically and horizontally according to the installation environment, which improves the ease of use. ...

Dynamic torque transducers can be used in the manufacture of viscometers, electric (pneumatic, hydraulic) torque wrenches, which have the advantages of high precision, fast frequency response, good reliability and long life. Installation process: 1. According to the connection form of the shaft and the length of the dynamic torque sensor, determine the original ...

Incremental sensors Only bearing change information is provided so that the practice bearing is unknown at startup. Each time the index is made/marks the zero or zero bit of the signaling community. Detected in the homing procedure. Regarding the commutation of brushless motors, motors generally have three magnetic Hall sensors, which are ...

The PSK1 series is a two-stage display pressure sensor that displays the current value (PV) and the set value (SV) together. It not only shows the setting status, but also provides a power-saving form and a fine-tuning function to improve the user's convenience. PSK1 Key Features: Additional pressure scale (composite pressure ...

Digital fiber optic sensors convert measured objects into measurable optical signal sensors. The principle of operation is to send the incident beam of the light source to the modulator through the optical fiber, and interact with the internal and external measurement parameters of the modulator to form a dimmable signal. Digital fiber optic sensors use ...

Dual PID auto-adjustment function There are high-speed response modes and slow reaction modes in the PID function. When you want to reach the desired value quickly, use the high-speed mode (PIDF mode) When you want to minimize overshoot, use slow mode (PIDS mode) ...

1. Measurement of action distance; When the action piece is close to the sensing surface close to the switch from the front, the distance close to the switch action is the action distance close to the switch, and the measured data should be within the parameters of the product. 2. Release distance ...