Buke touch screen unresponsive maintenance method

1. The servo mechanism is an automatic control system that enables the position, orientation, state and other output controlled quantities of the object to follow the arbitrary change of the input target (or given value). The servo mainly relies on the pulse to position, which can basically be understood in this way, the servo motor receives 1 ...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

On December 7, Buke was invited to participate in the "2020 China Mobile Robot (AGV/AMR) Industry Development Annual Conference" hosted by the People's Government of Songjiang District, Shanghai and hosted by the China Mobile Robot (AGV) Industry Alliance. At the same time, Buke has also won the "Annual Quality Supply Chain Award" for three consecutive years.

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

Cause of the failure 1) The sound wave reflection stripes on the four periphery of the surface sound wave touch screen are seriously dusty or scale, resulting in the touch screen not working. 2) The touch screen is malfunctioning. 3) The touch screen control card is faulty. 4) The touch screen signal line is faulty ...

1. Wide range of speed regulation 2. High positioning accuracy 3. There is sufficient transmission rigidity and high speed stability 4. Fast response, no overshoot In order to ensure productivity and processing quality, in addition to high positioning accuracy, it is also required to have a good and fast response ...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

(1) Azimuth share gain Sets the share gain of the azimuth ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the azimuth lag under the same frequency command pulse. However, too large a value may cause vibration or overshoot. The parameter values are determined by the detailed servo ...

AC motor speed regulation is achieved by changing the electrical parameters such as the power supply frequency, number of pole pairs and slip rate of AC motor. 1. Use the inverter to change the power supply frequency speed regulation, the speed regulation range is large, the stability and smoothness are good, and the mechanical characteristics are hard. It's just to add the amount ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1:11 alarm, control the power supply undervoltage, control the power inverter on P. The voltage between N is lower than the specified value. There are defects in the internal circuitry of the driver, etc. 2:12 alarm, control power supply overvoltage, control power inverter on P. N voltage exceeds the specified value, ...

On December 17, Buke Co., Ltd. and Willis Towers Watson (formerly Torrei Watson, the world's leading professional services company) held the "Buke Co., Ltd. Organizational Reform and Upgrade Project Kick-off Meeting". Xu Changliang, Chief Consultant of Willis Towers Watson, Sheng Shaoqin, Partner of Willis Towers Watson, Tang Dong, Chairman of Buke Group, Bu...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

In terms of the response speed of the servo drive: the torque mode has the smallest amount of calculation, and the driver responds the fastest to the control signal; The position mode is the most computationally intensive, and the driver is the slowest to respond to the control signal. When there are relatively high requirements for dynamic performance in motion, it is necessary to ...