Yaskawa MOTOMAN servo drive fault repair case summary (1-2)

Yaskawa Electric recently announced that its soft starter processing plant in Shanghai has resumed production since February 18. So far, the three processing plants of this Japanese-funded processing and manufacturing company in China have been fully opened. Last week, Yaskawa Electric in China processed two other ...

1. When the oscilloscope checks the current monitoring output of the driver, it is found that it is all noise and cannot be read; Cause of failure: The current monitoring output is not isolated from the AC power supply (transformer). Solution: It can be detected and observed with a DC voltmeter. 2. Motor ...

1. Before starting the machine, make sure that there is no one and no debris within the action range of the body, and check whether the control box is connected correctly with the body and other equipment 2. Check that the power supply matches the power supply required by the robot 3. Check the individual emergency stop and pause buttons to make sure they are functioning effectively 4. Ontology ...

A.F10: Power line is out of phase (the low voltage state of one phase of R, S, and T phases lasts for more than 1 second in the state of the main circuit power supply ON) Cause: Poor wiring of three-phase wires The three-phase power supply is unbalanced Single-phase AC power input is not set (Pn00E ...

The display of the teach-in programmer is a 5.7-inch color display. The available characters are English letters, numbers, symbols, katakana, hiragana, and kanji. In addition, when entering Japanese, you can also convert it to kana kanji by entering romaji. 　　Rotate [REMOTE] to enter the remote ...

1. First press "MENU to set collision detection". 2. Secondly, the collision detection status: set to enable for the collision detection to be effective. 3. Final sensitivity: the setting range is 1%-200%, and the default setting is 100%. ...

Japan's Yaskawa Electric famously created the first all-electric industrial robot, Motoman, in 1977, headquartered in the city of Kita-Kyushu, since its establishment in 1915, has gone from being called "Yaskawa Electric Japan as an automobile manufacturer", "Yaskawa Electric Automation Company of Japan" to "...

1. Open the control panel of Yaskawa Servo and select Manual Mode. 2. Manually rotate the rotor of the motor to calibrate the position of the motor; 3. Press the start button on the panel to let the motor start to rotate; 4. Using the speed adjuster on the panel, adjust the motor ...

1. Analysis of the causes of Yaskawa servo alarm C90 (AC9): 1. The encoder cable is broken or the encoder plug is made in poor process (there are also wiring errors in the alarm of the new machine); 2. The servo drive itself is faulty; 3. Environmental interference, caused by poor connection: ...

Yaskawa robot is a kind of industrial robot, which can be applied to various automated production lines according to its specifications and models, and the high-temperature work workshop is a major field where industrial robots are used more, so it needs to be protected by robot protective clothing. The following is a brief introduction to Ontor ...

1. Yaskawa servo alarm A840 (A84) is: encoder data error alarm. A.84 Common causes of alarm are: 1. Excessive mechanical vibration 2. High-frequency noise in the application environment 3. Servo motor inlet water inlet oil, dust, etc 4. The driver is faulty ...

In terms of speed: the servo motor + ball screw mode may resonate due to the change of load and mechanical design and installation when running at high speed, and the speed will be limited; The linear servo motor belongs to the direct drive, so the only factor that affects the speed is the linear servo motor itself.

At present, the mainstream servo drives all use digital signal processors (DSPs) as the control core, which can realize more complex control algorithms and realize digitalization, networking and intelligence. Power devices generally use the drive circuit designed with intelligent power module (IPM) as the core.

[10] Yaskawa servo back to the origin can not find the C phase pulse, Yaskawa servo drive and motor, using the travel switch + C phase back to zero mode, now the pressure on the switch deceleration can not find the C phase pulse, servo motor, drive, host computer, which fault is the most likely? A: Servo motor rotation ...

1. Turn on the power switch and compressed air switch of Yaskawa robot. 2. Turn on the main power switch on the Yaskawa robot control cabinet. After the robot completes the self-test, press the servo power button to turn on the servo power supply of the motor. Press the teach-in button (TEACH) on the control cabinet to make the machine ...

Yaskawa servo drives are used to control servo motors, which are similar to AC motors and are part of the servo system. The servo drive takes the digital signal processor as the control core, which can realize more complex control algorithms and realize digitalization, networking and intelligence. The present invention adopts the wisdom ...

Some methods when debugging Yaskawa servo drives In the Yaskawa servo system under low rigidity (1-4) load, the inertia ratio is very important, from the perspective of the synchronous belt structure, the stiffness is about 1-2 (or even less than 1), at this time, the inertia ratio can not be automatically tuned, it must be ...

Yaskawa YASKAWA inverter CH700 series is a product optimized for cranes with the product concept of versatility, ease of use, and peace of mind. Utilizing advanced technologies such as brake sequencing that incorporate 30 years of experience, we provide answers to a wide range of issues related to crane operation. 　　Yaskawa Y ...

OL2 is the inverter overload alarm, check whether it is a real overload or a false overload. 1. Test whether the output current of the inverter exceeds the rated current of the inverter, if it exceeds it, it may be the mechanical reason, if it does not exceed the inverter detection circuit is broken, and the false overload is reported. ...

Second, the wiring of the control circuit The control circuit of the inverter can be roughly divided into two types: analog and digital. 1. The wiring of the terminal of the control circuit should use shielded wire or twisted pair wire, and it must be separately routed from the main circuit and the strong current circuit (including the 200V relay program circuit). ...