Fault causes and solutions of Yaskawa servo alarm A840/A84

Yaskawa H1000 series is available in the following models H1000 Series Heavy Load 1. CIMR-HB4A006FAA/FAC/FBC 1·5KW H1000 replaces G7 series 2、CIMR-HB4A0075 30KW 3、CIMR-HB4A0045AAA 4、CIMR-HB4A0005FAA/FA ...

Yaskawa inverter V1000 series has amazing performance, wide range of uses, simple use and maintenance, and user-programmed function, breaking through the previous small inverter in every aspect and improving the level of all small machines. 1 multi-purpose (synchronous motor can also be driven). Detergent ...

1. Yaskawa robot teach pendant key switch to manual Teach mode - main menu - system information - security mode 2. Management mode - password - 999999999 3. Robot - Origin location 4. Open the door of the robot control cabinet and there is a mechanical prototype with 6 axes of the robot on the side.

Industrial robot is a multi-degree of freedom machine device, can automatically perform work, according to its own power and control ability to achieve various functions, by the mechanical part, sensing part, control part and other three parts, these three parts are divided into six subsystems, namely: 1. Drive...

1. Torque control mode: The torque control mode is to set the output torque of the motor shaft through the input of the external analog quantity or the assignment of the direct address, which is manifested as 10V corresponding to 5Nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5Nm: if the electric ...

1. If the fault code on the Yaskawa inverter is UV1, then it means that the low voltage of the main circuit is lower than the low voltage standard of 200V, at this time, we need to check whether there is a problem with the wiring of the power supply; 2. If the fault code appears on the Yaskawa inverter ...

First, the wiring of the main circuit 1. The power supply should be connected to the R, S, and T terminals at the input end of the inverter, and must not be connected to the output terminal (U, V, W) of the inverter, otherwise the inverter will be damaged. After wiring, the fragmented wires must be cleaned, and the fragmented wires may cause abnormalities. ...

Yaskawa servo drive alarm code 710 is overload (large load), the motor is overloaded for a few seconds to tens of seconds. Solution(s): 1. Change the mechanism, or the acceleration and deceleration mechanism. 2. Change the motor. 3. Exclusion order: 1) The load is really too large 2) ...

Today I would like to introduce to you what models are available in the E1000 and V1000 series: E1000 fan pump type 1、EB4A0058 2、EB4A0002 3、EB4A0005 4、EB4A007 5、EB4A0011 6、EB4A0004 V1000 Series ...

Attention to the wiring of the inverter 1. The inverter itself has strong electromagnetic interference, which will interfere with the work of some equipment, so we can add a cable sleeve to the output cable of the inverter. 2. The control line in the inverter or control cabinet is at least 100mm away from the power cable, etc. ...

In order to realize the anti-collision function of Yaskawa robots, there are two ways to connect external sensors, which are described below; In addition, how to dismiss alarms will be described in this article. 01. Directly connect to an external collision sensor 1. The machine in the door of the control cabinet ...

1. Hydraulic coupling mode. That is, a hydraulic coupling device is inserted between the motor and the load in series, and the size of the coupling force between the motor and the load is adjusted by the height of the liquid level, so as to realize the speed adjustment of the load; 2. Cascade speed regulation. The cascade speed regulation must use a wound asynchronous motor, which ...

Yaskawa Electric, one of the world's largest manufacturers of industrial robots, announced a 150% year-on-year increase in net profit for the six months ended Sept. 30. The Japan company announced that the company reported a profit for the quarter due to the demand for its industrial robots in China, Japan and United States.

1. Check whether the encoder cable is good and carefully check the coding cord plug. Whether the soldering points and cable bow and foot row are normal; 2. If no wire and plug problems are found, rule out the interference of the encoder cable, please separate the encoder cable from other wires (power cables); 3. Line ...

Q: How often is the robot maintained? A: Generally speaking, the frequency of scheduled maintenance of the robot should be determined on a case-by-case basis. It is generally recommended to carry out a full maintenance every 3-6 months, but for high-intensity and long-working robots, more frequent maintenance may be required.

The following are the common faults of the inverter and how to deal with them 1) OC Over Current This is the most frequent failure of the inverter, and it is divided into external and internal causes in the analysis of causes. External causes: mechanical structure and parameter setting, open-loop control ...

1. When the control power supply is put in, it is caused by the failure of the servo unit circuit board, and the servo unit needs to be replaced. 2. When it occurs in servo ON, then it is caused by the failure of the servo unit circuit board or the short-term motor power line, and the servo unit or motor needs to be replaced.

1. Hydraulic drive system Because hydraulic technology is a relatively mature technology. It has the characteristics of large power, large force (or moment) to inertia ratio, fast response and high response, and easy to realize direct drive. It is suitable for working in large load-bearing capacity, large inertia and solder-mask environments.

H1000 The new Yaskawa "H1000" heavy-duty inverter plays a stable and outstanding role in the heavy-duty industrial field! Capacity range 200V class 0.4-110kW 400V class 0.4 - 355kW apply Lifting Machinery, Fluid Machinery, Metalworking Machines ...

1. First press "MENU to set collision detection". 2. Secondly, the collision detection status: set to enable for the collision detection to be effective. 3. Final sensitivity: the setting range is 1%-200%, and the default setting is 100%. ...