Introduction: The speed of an incremental encoder is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. The dual-channel output encoder has two signals with a 90-degree phase difference, which allows the controller to determine the direction of rotation and realize the position measurement function in both directions. In addition, the three-channel incremental encoder has a third signal channel (i.e. the "0" channel, or reference channel) with only one pulse output per revolution.
Features:
Industrial standard housing 58 mm
Up to 5000 ppr
Servo flanges, square flanges or clamping flanges
Special flanges for special shafts are required
Stainless steel version
10 V … 30 V with RS 422 interface
Product parameters
General specifications
Pulse count max. 5000
Electrical Specifications
Operating voltage 10 ... 30 V DC
No-load current: 150 mA max
yield
Output type RS 422, incremental
Load current max. 20 mA per channel, conditional short-circuit protection, reverse polarity protection
Output frequency: 100 kHz max
Rise time: 100 nanoseconds
Power-off delay of 100 nanoseconds
connect
Connector Model 42306 (M16), 6-pin
Type 42308 (M16), 8-pin
Type 9414 (M16), 5-pin
Type 9416 (M23), 12-pin
Cable ∅6 mm, 4×2×0.14 mm 2,2 m
Standards Compliance
Degree of protection DIN EN 60529, IP65
Climatic test DIN EN 60068-2-3, non-condensing
Emission interference EN 61000-6-4:2007 / A1:2011
Noise immunity EN 61000-6-2:2005
Approvals and certificates
UL Listed cULus General Purpose Class 2 Power Supplies
Environmental conditions
Operating temperature
Glass Dish -20 ... 70°C（-4 … 158°F）
Plastic Plate -20 ... 60°C（-4 … 140°F）
Storage temperature
Glass Plate -40 ... 70°C（-40 … 158°F）
Plastic Disc -40 ... 60°C（-40 … 140°F）
Mechanical Specifications:
material
Combo 1 Housing: Die-cast zinc
Flange: Aluminum 3.1645
Shaft: Stainless steel 1.4305 / AISI 303
Combination 2 (Stainless Steel) Housing: Stainless steel
Flange: stainless steel
Shaft: stainless steel
Block approx. 335g (set 1)
Approx. 1400g (Set 2)
Rotational speed max. 10000 minutes - 1
The moment of inertia ≤30gcm2
Starting torque ≤ 1.5 Ncm
Axle load
60 N axial
Radial 80 N
The company respects the enterprise spirit of "practicality, hard work and responsibility", and creates a good corporate environment with integrity, win-win, and business philosophy, and takes a new management model, perfect technology, thoughtful service, and excellent quality as the foundation for survival. We always adhere to: customer first, serve customers attentively, and insist on impressing customers with their own services. Always adhering to the business philosophy of "integrity, win-win", relying on excellent prices, excellent quality, fast delivery and pre-sales consultation and after-sales service to win the trust of our customers.
This article introduces the P+F incremental rotary encoder 10 - 2133 X product, if you are interested in P+F incremental rotary encoder, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F Inductive Positioning System PMI120-F90-IU-IO-V15
Introduction:P+F Inductive Positioning System PMI120-F90-IU-IO-V15 Reverse Polarity Protection, Analog Current or Voltage Output, Programmable; Linearity ranges from 1 to 119 mm; PBT, stainless steel 1.4571, brass, nickel-plated housing.
...
|
|
P+F/Radiator LA31/LK31/31/115 LEDs
Product Description: Thru-beam sensor, 30 m detection range, red light, switch-on on bright, AC/DC type, relay output, fixed cable, cost-optimized series for standard tasks, small housing for large structures, high visibility LED, universal voltage version, relay output. ...
|
|
P+F inductive sensor NBN4-12GM60-A0 4mm
Introduction: Inductive proximity sensors are the product of choice for most applications that require high-precision, non-contact detection of metal targets in the field of mechanical instrumentation and automation equipment. As a market leader in this category, we offer our customers innovative, high-quality ...
|
|
P+F/GJF retro-reflective sensor GLV18-55/115/120
Product Description: Retroreflective sensor with polarization filter, M18 threaded housing design, plastic housing, front optical face, 4 m detection range, red light, light and dark on, DC type, 2 PNP output, fixed cable, high-efficiency wire in M18 plastic housing Standard application, very high detection range
|
|
P+F/M100/MV100-6090/102/115 through-beam photoelectric sensors
Product Introduction: Thru-beam sensor, miniature design, miniature sensor light forming slit, easy to use, very bright, high visible light point, full metal threaded mounting.
Our customer-centric service concept: the pursuit of a full range of services is a ...
|
|
P+F/Capacitive sensor CJ6-18GK-N with a conductor cross-section of 0,75mm2
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Optical Data Coupler DAD15-8P Spring Terminals
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F sensor NBN40-L2-E0-V1 40 mm non-flush
Introduction: NBN40-L2-E0-V1 is a kind of switch sensor (i.e., non-contact switch), which has the characteristics of travel switch and micro switch, and has sensing performance, and reliable action, stable performance, fast frequency response, long application life, strong anti-interference ability, etc.
|
|
P+F/Diffuse Mode Sensor GLV18-8-450 /73/120
Product Introduction: Diffuse Mode Sensor, M18 Threaded Housing Design, Plastic Housing, Front Optical Surface, 450 mm Detection Range, Red Light, Light & Dark, DC Type, 2 PNP Outputs, M12 Plug, High Efficiency Circuit in M18 Plastic Housing, For Standard Applications, Very High Detection Range, 4 ...
|
|
P+F/Reflector Type Photoelectric Switches ML100-55/103/115 Compact
Product Introduction:Retroreflective Plate Sensor with Polarization Filter, Plastic Housing, 5 m Detection Range, Red Light, Adjustable Sensitivity, Switch-On When Bright/Dark, DC Type, PNP Output, Fixed Cable, Compact Design, Easy to Use, Clear LED Indication, Power Supply, Switching Status, Stable ...
|
|
P+F/Capacitive sensor CJ30-50K10-E0123-Y46139 cable 2m
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/UB1000-18GM75-E5-V15
Product Introduction: The transducers used to transmit and receive sound waves are separated, so that the system does not need to wait for the signal attenuation of the transmitter, thus effectively reducing the dead zone. The direct detection type of ultrasonic sensors is available with switching and analog outputs. Direct detection of all support window mode functions ...
|
|
P+F/Through-beam photoelectric sensors LD31/LV31/76a/115/136
Product Description: Thru-beam sensor, 30 m detection range, red, low, DC version, 2 push-pull outputs, transmitter off, fixed cable, high visibility LED, powerful push-pull output, compact and stable housing, degree of protection II
Our customer-centric ...
|
|
P+F/Double Blessing Timer KC-LCDC-48-2R-230VAC 142g
Introduction: P+F Timer KC-LCDC-48-2R-230VAC easy-to-read, backlit 2-line LCD display with icons for pre-selection and the status of both outputs; Add/subtract via 2 independent inputs, degree of protection IP65 (front).
...
|
|
P+F Inductive Sensor NBB8-18GM60-US 8mm
Summary: Inductive proximity sensors are the product of choice for most applications that require the precise and non-contact detection of metal objects in machinery or automation. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality inductors.
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40A-SE2-V1
Introduction: There is no electrical connection between the transmitter and receiver, and while the sensor is mounted in such a way that it does not affect the functionality of the ultrasonic through-beam sensor, it is recommended to mount the transmitter face up when the sensor is mounted vertically to prevent the accumulation of dust particles.
...
|
|
P+F/Accelerometer ACX04-F99-I-V15 outputs 4 mA~20 mA
Product Introduction: The F99 series accelerometer monitors the strong vibration or acceleration of the wind turbine due to high winds. The sensor has a rugged, environmentally friendly housing and uses a non-contact, reliable detection principle to avoid critical situations.
Specifications:
...
|
|
P+F/Capacitive sensor CBN15-F64-A2 15mm non-flush
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40-SE2-V1 PNP
Product introduction: The working principle of ultrasonic through-beam sensor is to detect an object by emitting sound waves from the transmitter to the receiver and being interrupted by the sound beam by the target object. The transmitter generates an ultrasonic signal that is received and evaluated by the receiver. When the ultrasonic beam is attenuated or interrupted by an object, the receiver ...
|
|
P+F/Inductive sensor NBB8-18GM50-E0 8mm flush
Introduction:P+F/Beijiafu inductive sensor NBB8-18GM50-E0 has a detection distance of 8mm and is installed flush; It has a longer working distance; Extended temperature range; -40 to +85 °C; Extended operating voltage range; With a variety of mounting options, it is flexible to use.
...
|
|
Contact
working hours
