Product Description: Thru-beam sensor, 30 m detection range, red light, switch-on on bright, AC/DC type, relay output, fixed cable, cost-optimized series for standard tasks, small housing for large structures, high visibility LED, universal voltage version, relay output.
Product Description | | Through-beam photoelectric sensor, 30 m detection range, red light, bright on, AC/DC type, relay output, fixed cable |
System components | | Transmitters | LA31/115 | | receiver | LK31/25/31/115 | General specifications | | Effective detection distance | 0 ... 30 m | | Detection range limit values | 43 m | | light source | LED | | The type of light source | Modulated visible red light, 630 nm | | Alignment aids | Yellow LED:
1. LED is lit: Enough light signal is received, and the transmitter and receiver are properly aligned
2. LED flashing: Reach the switch point
3. LED off: The beam is interrupted or misaligned | | Spot diameter | Approximately 800 mm are 30 m apart | | Divergence angle | Transmitter: 0,5 ° , Receiver: 1,5 ° | | Ambient light limitations | 50000 Lux ; According to EN 60947-5-2 | Functional safety-related parameters | | MTTFd | 620 a | | Mission Time (TM) | 20 a | | Diagnostic Coverage (DC) | 0 % | Indicator/method of operation | | Work indicator | Green LED: Powered on | | Function indicator | Yellow LED:
1. LED is always on: signal > 2 x switching points (function reserved)
2. LED flashing: The signal is between 1 x switch and 2 x switch points
3. LED off: signal < switch point | Electrical Specifications | | Operating voltage | 24 ... 240 V AC
12 ... 240 V DC | | No-load current | Emitter: ≤ 20 mA
Receiver: ≤ 20 mA | | power consumption | Transmitter: ≤ 1 VA
Receiver: ≤ 1 VA | output | | Switch type | Turn on when it's on | | Signal output | Relay, 1 alternator | | Switching voltage | 250 V AC/DC max | | Switching current | 3 A max | | Switching power supplies | DC: 150 W max. AC: 750 VA max | | Switching frequency | ≤ 20 Hz | | Response time | ≤ 25 ms | compliance | | Product standards | EN 60947-5-2 | Compliance with standards and directives | | Meets standards | | | standard | EN 62103 | Certifications and certificates | | EAC Conformity | TR CU 020/2011
TR CU 004/2011 | | Ingress protection | II, When the pollution class is 1-2 (according to IEC 60664-1), the rated voltage is ≤ 250 V AC The output circuit of the input circuit is basically insulated according to EN 50178 and the rated insulation voltage is 240 V AC | | CCC certified | Passed China Compulsory Certification (CCC) | Environmental conditions | | Ambient temperature | -25 ... 55 °C (-13 ... 131 °F) | | Storage temperature | -40 ... 70 °C (-40 ... 158 °F) | Mechanical Specifications: | | Enclosure width | 18 mm | | Enclosure height | 62 mm | | Enclosure depth | 35 mm | | Ingress protection | IP67 | | connect | Transmitter: 2 m fixed cable, 2 wires
Receiver: 2 m fixed cable, 5 wires | | material | | | enclosure | polycarbonate | | Optical end faces | PUMA | | quality | Transmitter: 116 g
Receiver: 131 g |
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action and every detail of the service is professional and careful, can we meet or even exceed the expectations of customers, so that customers can be satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F/Bulb Photoelectric Sensor LA31/LK31/25/31/115 products, if you are interested in P+F/P+F/Bulb Photoelectric Sensor, please also contact our staff, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F magnetic field sensor MMB60-12H50-E2-V1 60 mm
Introduction: Magnetic sensors with M12 cylindrical housing are used in conventional magnet detection. A non-contact detection sensor for piston position is also available for steel hydraulic cylinders. These sensors are easy to install and do not require a mounting slot or installation in the cylinder.
|
|
P+F/Capacitive sensor CJ40-FP-A0-P1 has a voltage drop of ≤ 2.8 V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Print Marks Contrast Sensor DK12-11-IO/92/136 M12 plug
Introduction: Colour mark sensors can be used to detect registered trademarks in printing, converting, packaging, food, beverage, and pharmaceutical processes for sorting, positioning, and quality control of goods. The P+F color scale sensor is characterized by low contrast detection at high resolution, loud ...
|
|
P+F/Beam Ultrasonic Barrier UBE4000-30GM-SA2-V15 nickel-plated brass
Introduction: There is no electrical connection between the transmitter and receiver, and while the sensor is mounted in such a way that it does not affect the functionality of the ultrasonic through-beam sensor, it is recommended to mount the transmitter face up when the sensor is mounted vertically to prevent the accumulation of dust particles.
...
|
|
Germany P+F/Beijiafu inductive sensor NBN4-F25-2Z4L weight 405g
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/UBE15M-F54-H1-V1 housing PBT
Introduction: An ultrasonic through-beam sensor consists of a transmitter and a receiver mounted facing each other. Ultrasonic through-beam sensors work by emitting sound waves from the transmitter to the receiver to detect objects through the sound beam being interrupted by the target object. The emitter produces ultrasonic ...
|
|
P+F/Switching Amplifier KFD2-SOT3-Ex2 24V DC
Introduction: The K-series isolation barriers provide users with a comprehensive solution to ensure reliable & economical signal transmission between field devices and control rooms. Whether the user selects a single signal isolation module or performs large-scale system integration, the K Series ...
|
|
P+F/Capacitive sensor CBN15-30GK60-E2-5M with a diameter of 30mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CJ10-30GM-WS current: 5~200mA
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F inductive sensor NBB2-12GM50-E3-V1 2 mm
Introduction: Smooth or threaded stainless steel cylindrical housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR output mode to ...
|
|
P+F/Capacitive sensor CBN15-F64-A2 15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Optical Data Coupler DAD15-8P Spring Terminals
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F/UB1000-18GM75-E5-V15
Product Introduction: The transducers used to transmit and receive sound waves are separated, so that the system does not need to wait for the signal attenuation of the transmitter, thus effectively reducing the dead zone. The direct detection type of ultrasonic sensors is available with switching and analog outputs. Direct detection of all support window mode functions ...
|
|
P+F Capacitive sensor CCB10-30GS55-N1-V1
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Capacitive sensor CJ2-18GK-N 2mm non-flush mounting
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CJ4-12GK-N 4mm non-flush
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
...
|
|
P+F/Capacitive sensor CBN15-30GK60-A0 NPN15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/IBN4-F29-E0 Inductive Proximity Sensor 4mm Non-flush
Introduction: P+F inductive proximity sensor NBN4-F29-E0 reverse polarity protection, pulse short circuit protection, off-state current 0 ... 0,5 mA Type 0,1 μA At 25 °C and rated voltage ≤ 36 V, the product does not require CCC certification/marking.
...
|
|
Germany P+F/Bejiafu capacitive sensor CJ15+U4+A2 four-wire DC
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Double Sheet Sensor UDC-18GM-400-3E1-Y194142
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
Contact
working hours
