Introduction: There is no electrical connection between the transmitter and receiver, and while the sensor is mounted in such a way that it does not affect the functionality of the ultrasonic through-beam sensor, it is recommended to mount the transmitter face up when the sensor is mounted vertically to prevent the accumulation of dust particles.
Specifications:
General specifications | Sensing range | 15 ... 1000 mm | Standard target plates | 100 mm× 100 mm | Sensor frequency | About. 255 kHz | Indicators/means of operation | LED green | Open it | LED yellow | Switch status | LED red | Error, the object is not determined | Electrical Specifications | Operating voltage | 10 ... 30 V DC, ripple 10% SS | No-load current | ≤20 mA | input | Enter the type | 1. Program input
Free air path: -U B ... +1 V, Object: +6 V ... + U B
Input impedance: > 4,7 k Program pulse: ≥1 s | yield | Output type | PNP，NO | Rated operating current | 200 mA, short-circuit/overload protected | Voltage drops | ≤3 V | Turn on latency | <5 ms | Switching frequency | ≤100 Hz | Approvals and certificates | UL recognized | cULus listed, generic | CSA approved | cCSAus listed, generic | CCC approved | Products with a rated voltage of ≤ 36V do not require CCC certification/marking | Environmental conditions | Ambient temperature | -25 ... 70°C（-13 ... 158°F） | Storage temperature | -40 ... 85°C（-40 ... 185°F） | Mechanical Specifications: | Connection type | Connector M12 x 1,4 pins | Ingress protection | IP67 | material | | | housing | Brass, nickel-plated | | sensor | epoxy/hollow glass sphere mixture; Foamed polyurethane, covered with PBT | block | 25 grams |
The company has been customer-centric, the concept of creating value for customers, winning the market with quality and service, and sincerely hopes to cooperate with all sectors of society to create success, create brilliance together, and work together to create a better tomorrow! In line with the concept of credibility and service-oriented, the company warmly welcomes new and old customers to inquire, visit and negotiate business!
|
More on that
|
Germany P+F/Bejiafu capacitive sensor CJ15+U4+A2 four-wire DC
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Sensor NBN4-12GM60-A2-V1 4 mm non-flush
Introduction: NBN4-12GM60-A2-V1 standard inductive sensor smooth or threaded stainless steel cylindrical housing; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, ...
|
|
P+F inductive sensor NBN4-12GM60-A0 4mm
Introduction: Inductive proximity sensors are the product of choice for most applications that require high-precision, non-contact detection of metal targets in the field of mechanical instrumentation and automation equipment. As a market leader in this category, we offer our customers innovative, high-quality ...
|
|
P+F/Optical Data Coupler LS682-DA-EN / F1 Fast Ethernet
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
Germany P+F/Bejiafu capacitive sensor CBN10-F46-E2-0,4M-V3
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Reflective Plate Photoelectric Switch ML100-55/95/103 360 degree view
Product Description: Retroreflective sensor with polarization filter, plastic housing, 5 m detection range, red light, adjustable sensitivity, on/off when light/dark, DC type, PNP output, M8 plug, compact design, easy to use, extremely bright and clear light spot, all-metal threaded mounting, ...
|
|
P+F/Encoder RVI58N-*******1 Incremental
Introduction: An incremental encoder provides a fixed number of pulses in one revolution, and the speed is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. The accuracy of incremental encoders depends on mechanical and electrical factors ...
|
|
P+F Multiturn Absolute Encoder AVM58-H
Introduction: In this construction, the gear structure is added on the basis of the singleturn code disc, through these interconnected gears, we can measure up to 16,384 turns (14 bits), so that the total accuracy of the encoder is 16 bits (single turn) plus 14 bits (number of turns), or the total precision ...
|
|
P+F/Encoder RVI50N-09B**A*T 80mA
Introduction: An incremental encoder provides a fixed number of pulses in one revolution, and the speed is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. The accuracy of incremental encoders depends on mechanical and electrical factors ...
|
|
P+F/Sensor NBN4-12GM40-E2-V1 4 mm
Introduction: The inductive sensor is to use electromagnetic induction to convert the measured physical quantities such as displacement, pressure, flow, vibration, etc. into the change of self-inductance coefficient and mutual inductance coefficient of the coil, and then convert the output of voltage or current change by the circuit to realize the conversion of non-electricity to electricity.
...
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40-SE2-V1 PNP
Product introduction: The working principle of ultrasonic through-beam sensor is to detect an object by emitting sound waves from the transmitter to the receiver and being interrupted by the sound beam by the target object. The transmitter generates an ultrasonic signal that is received and evaluated by the receiver. When the ultrasonic beam is attenuated or interrupted by an object, the receiver ...
|
|
P+F/Capacitive sensor CJ40-FP-A0-P1 has a voltage drop of ≤ 2.8 V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F Inductive Sensor NBB15-30GM50-E0 15mm
Introduction: P+F Inductive Sensor NBB15-30GM50-E0 15mm flush; Longer working distance; Extended temperature range -40 ... +85 °C; Extended operating voltage range; With a variety of mounting options, it is flexible to use.
...
|
|
P+F/Capacitive sensor CBN15-30GK60-E2-5M with a diameter of 30mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Double Sheet Sensor UDC-18GM50-255-3E1 Current < 65 mA
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F/Capacitive sensor CJ10-30GM-WS current: 5~200mA
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Through-beam photoelectric sensors LD31/LV31/73c/76a/136
Product Description: Thru-beam sensor, 30 m detection range, red light, switch-on on bright, AC/DC type, relay output, fixed cable, cost-optimized series for standard tasks, small housing for large structures, high visibility LED, universal voltage version, relay output. ...
|
|
P+F/Capacitive sensor CJ30-50K10-E0123-Y46139 cable 2m
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN10-F46C-EI 7mm
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Inductive sensor NBN30-L2-E2-V1 30 mm
Introduction: Smooth or threaded stainless steel cylindrical housing for standard inductive sensors; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR output ...
|
|
Contact
working hours
