Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards the proximity switch, regardless of whether it is a conductor or not, due to its proximity, the dielectric constant of the capacitor must change, so that the capacitance changes, so that the state of the circuit connected to the measuring head also changes, so that the switch can be switched on or off. This proximity switch detects not only conductors, but also liquids and powders that can be insulated.
Product Information
Switch Function: Normally Open (NO)
Output Type: NAMUR
Rated working distance: 6 mm
Installation: Non-flush
Reliable operating distance :0 ... 4,32 mm
Output Type: 2-wire
Rating:
Installation conditions
A ：40 mm
B ：80 mm
C ：20 mm
F ：120 mm
Rated voltage: 8,2 V (Ri approx. 1 kΩ)
Operating voltage :7 ... 12 V
Switching frequency: 0 ... 1 Hz
Current consumption
Measuring plate not detected: ≤ 1 mA
Measuring plate detected: ≥ 2,4 mA
Functional safety parameters
Mean time to failure (days): 5030 a
Service life (...) Month... days): 20 a
Diagnostic range: 0 %
Consistency with standards and norms:
Meets standards
NAMUR EN 60947-5-6:2000
IEC 60947-5-6:1999
Licensing & Certification:
FM certification
Control chart: 116-0165
UL Listed: cULus Listed, general requirements
CSA Listed: cCSAus Listed, General Purpose
CCC approval: Products with a maximum operating voltage of 36 volts do not need to be certified and therefore do not need to be equipped with the CCC-mark.
Ambient temperature :-25 ... 70 °C （-13 … 158 °F）
Mechanical properties
Connection type : cable PVC, 2 m
Conductor cross-section: 0,75 mm2
Housing material :P BT
Sensing surface :P BT
Degree of protection: IP68
cable
Bend radius: > 10 x cable diameter
General Instructions:
Grade 1G; 2G; 1D
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action, and every day of service are professional and careful, can we meet or even exceed customer expectations, so that customers can be satisfied and recognized by us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F/Double Capacitive Sensor CJ6-18GK-N products, if you are interested in P+F/Double Capacitive Sensor, please also contact our staff, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F/Double Sheet Sensor UDC-18GM-400-3E1-Y194142
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F/Capacitive sensor CBN15-F64-A2-0, 3M-V1
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F capacitive sensor CBN15-18GS75-E2-V1 is non-flush
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F inductive sensor NBN5-F7-E0 5 mm non-flush
Introduction: P+F inductive sensor NBN5-F7-E0 5 mm non-flush, switch function normally open (NO), output type NPN, rated working distance 5 mm, installation non-flush, output polarity DC, ensure operating distance 0 ... 4,05 mm
...
|
|
P+F/Bi-material sensor UDC-18GM50-255S-3E0
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F/Optical Data Coupler LS682-DA-EN / F1 Fast Ethernet
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F/Diffuse Mode Sensor GLV18-8-450 /73/120
Product Introduction: Diffuse Mode Sensor, M18 Threaded Housing Design, Plastic Housing, Front Optical Surface, 450 mm Detection Range, Red Light, Light & Dark, DC Type, 2 PNP Outputs, M12 Plug, High Efficiency Circuit in M18 Plastic Housing, For Standard Applications, Very High Detection Range, 4 ...
|
|
P+F/Through-beam photoelectric sensors LD31/LV31/76a/115/136
Product Description: Thru-beam sensor, 30 m detection range, red, low, DC version, 2 push-pull outputs, transmitter off, fixed cable, high visibility LED, powerful push-pull output, compact and stable housing, degree of protection II
Our customer-centric ...
|
|
P+F Capacitive sensor CCB10-30GS55-N1-V1
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F capacitive sensor CBB10-30GKK-A2 10mm flush
Introduction:P+F Capacitive Sensor CBN5-F46-E2-10M Flat Housing; reverse polarity protection; Fixing slot for cable tie, through-hole for screw mounting, cULus listed, general use.
Product parameters
...
|
|
P+F/Capacitive sensor CBN15-F64-A0 has a voltage drop of ≤2V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40A-SE2-V1
Introduction: There is no electrical connection between the transmitter and receiver, and while the sensor is mounted in such a way that it does not affect the functionality of the ultrasonic through-beam sensor, it is recommended to mount the transmitter face up when the sensor is mounted vertically to prevent the accumulation of dust particles.
...
|
|
P+F/Double Blessing Timer KC-LCDC-48-2R-230VAC 142g
Introduction: P+F Timer KC-LCDC-48-2R-230VAC easy-to-read, backlit 2-line LCD display with icons for pre-selection and the status of both outputs; Add/subtract via 2 independent inputs, degree of protection IP65 (front).
...
|
|
P+F/Logic Control Device 14bit Resolution
Introduction: Logic control units are widely used in the automation industry. In practice, they are capable of detecting digital or analog signals, displaying them and monitoring them. In order to solve the conversion and application between signals, we provide digital display meters, counters ...
|
|
P+F/Sensor NBN4-12GM60-A2-V1 4 mm non-flush
Introduction: NBN4-12GM60-A2-V1 standard inductive sensor smooth or threaded stainless steel cylindrical housing; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, ...
|
|
P+F/Through-beam GD18 / GV18 /115/120
Product Introduction: Thru-beam sensor, M18 threaded housing design, plastic housing, front optical surface, 20 meters detection distance, red light, light and dark, DC version, 2 PNP outputs, fixed cable, high efficiency line, short M18 plastic housing application, very high detection range, 4 LED fingers...
|
|
P+F inductive sensor NBB2-V3-E2 normally open 2 mm
Introduction: Inductive proximity sensors are the most advanced products for most applications, ranging from mechanical instruments and automation equipment to the need for high-precision, non-contact detection of metal targets. As a market leader for this type of product, we offer our customers innovative and high-quality inductive ...
|
|
P+F/Capacitive sensor CBN5-F46-E0-Y286690 distance 5mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Inductive sensor NCB1,5-8GM25-N0-Y295009
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR...
|
|
P+F/Capacitive sensor CBN7-F46-E1-Y291652 3-wire DC
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
Contact
working hours
