Parameterization steps of Yaskawa inverter

As a long-standing and reliable supplier of automated metalworking solutions, Yaskawa will be exhibiting at AMB for the first time. Possible applications for the company's Motoman robots include tool handling, machining and stacking workpieces, and machine loading. At booth 6D50 in Hall 6, ...

1. If the fault code on the Yaskawa servo drive is UV1, it means that the low voltage of the main circuit is lower than the low voltage standard of 200V, at this time, we need to check whether there is a problem with the wiring of the power supply; 2. If the ...

1. Hydraulic drive system Because hydraulic technology is a relatively mature technology. It has the characteristics of large power, large force (or moment) to inertia ratio, fast response and high response, and easy to realize direct drive. It is suitable for working in large load-bearing capacity, large inertia and solder-mask environments.

1. Determine mechanical specifications, load, rigidity and other parameters; 2. Confirm the action parameters, stroke, accuracy, acceleration and deceleration time, cycle, moving speed, etc.; 3. Select motor inertia, load inertia, motor axis conversion inertia, and rotor inertia; 4. Select the motor back ...

First, the servo dispute settings are too large, and it is recommended to readjust the servo parameters manually or automatically. Second, make sure that the initial value of the time constant of the velocity feedback filter is set to zero, and try increasing the initial value. Thirdly, the electronic gear ratio setting is too large, it is recommended to restore ...

01. The robot switch often jumps or can't close? Cause: 1. Aging of switches; 2. The switch selection is wrong; 3. The pump is stuck or the motor is short-circuited; 4. The line is aging, short circuit, the line is too small or the phase is missing. Solution: Convert the control ...

First, the wiring of the main circuit 1. The power supply should be connected to the R, S, and T terminals at the input end of the inverter, and must not be connected to the output terminal (U, V, W) of the inverter, otherwise the inverter will be damaged. After wiring, the fragmented wires must be cleaned, and the fragmented wires may cause abnormalities. ...

1. Carefully monitor and record the display parameters on the man-machine interface of the inverter, and reflect the abnormality immediately 2. Carefully monitor and record the ambient temperature of the inverter room, and the ambient temperature should be between -5 °C and 40 °C. The temperature rise of the phase-shifting transformer should not exceed 130°C 3. Summer ...

First, the basic wiring The main power input is 220V, which is connected from L1 and L3 (the actual use should refer to the operation manual); The control power input r and t can also be directly connected to 220V; See pages 22 and 23 of the operation manual for motor wiring, and see the operation manual for encoder wiring.

1. The LED light is green, but the motor does not move (1) Cause of failure: The motor in one or more directions is prohibited from operating. Solution: Check the +INHIBIT and –INHIBIT ports. (2) Cause of failure: The command signal is not to the driver signal. ...

For the maintenance of Yaskawa robots, maintenance should be carried out before and after each use, check whether there is damage to the outside of the robot, and check whether the robot movement is abnormal. Then be sure to check the battery frequently, and if you find that the battery is not working, you should replace it as soon as possible. The gearbox should be checked frequently to see if there is ...

Founded in 1989, Yaskawa Motoman is a leading industrial robotics company in the Americas. With more than 400,000 Motoman industrial robots, 15 million servos and 26 million inverter drives installed worldwide, Yaskawa provides automation products and ...

Attention to the wiring of the inverter 1. The inverter itself has strong electromagnetic interference, which will interfere with the work of some equipment, so we can add a cable sleeve to the output cable of the inverter. 2. The control line in the inverter or control cabinet is at least 100mm away from the power cable, etc. ...

1. The LED light is green, but the motor does not move (1) Cause of failure: The motor in one or more directions is prohibited from operating. Solution: Check the +INHIBIT and –INHIBIT ports. (2) Cause of failure: The command signal is not to the driver signal. ...

Q: How often is the robot maintained? A: Generally speaking, the frequency of scheduled maintenance of the robot should be determined on a case-by-case basis. It is generally recommended to carry out a full maintenance every 3-6 months, but for high-intensity and long-working robots, more frequent maintenance may be required.

(1) Open modular control system architecture: using distributed CPU computer structure, divided into robot controller (RC), motion controller (MC), optoelectronic isolation I/O control board, sensor processing board and programming teaching box, etc. The Robot Controller (RC) and the programmed teaching pendant are connected via a string...

1. Open the control panel of Yaskawa Servo and select Manual Mode. 2. Manually rotate the rotor of the motor to calibrate the position of the motor; 3. Press the start button on the panel to let the motor start to rotate; 4. Using the speed adjuster on the panel, adjust the motor ...

1. The inverter shows that SC refers to the drive fault. 2. Cause of failure: 1. The output side of the inverter is interphase or short circuit to the ground. 2. The inverter module is damaged. 3. Handling method: 1. Remove the load, power on normally and turn on the machine, check if there is a three-phase ...

1. Open the parameter setting interface of the servo drive and find the invert parameter setting option. 2. Set the inversion parameters, including the inversion voltage, inversion speed, etc. Depending on the specific situation, the reversal voltage can be set to -10V and the reversal speed to 1000RPM. 3. After saving the settings ...

1. Torque control mode: The torque control mode is to set the output torque of the motor shaft through the input of the external analog quantity or the assignment of the direct address, which is manifested as 10V corresponding to 5Nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5Nm: if the electric ...