When it is required to wiring outside the frequency conversion cabinet, it is generally necessary to use the conduit for wiring, which requires suitable mechanical pressure and unsuitable mechanical damage, moisture-proof and corrosion-resistant. Conduits include the following two wiring methods:
1. Metal hose wiring:
Metal hose wiring is suitable for the connection between various electrical appliances or equipment belonging to the production machinery itself. The standard of the hose is confirmed according to the total section of the pipe conductor, and there are joints at both ends of the hose to ensure the connection; When laying, the central part should be fixed with a suitable pipe clamp; Do not use damaged or defective hoses.
2. Iron pipe wiring:
Attention should be paid to the following matters in the wiring of iron pipes.
(1) The type and diameter of the iron pipe should be selected according to the occasion of application, the cross-sectional area of the wire and the number of wires, and 40% of the pipe should be left.
(2) When laying the catheter, try to make the interval as short as possible and the least twists and turns. When it is necessary to bend, the bending radius should be greater than 4 - 6 times the diameter of the pipe. There should be no cracks after twists and turns. When the pipeline is out of the ground, the height from the ground should be more than 0.2m
(3) The wires of the same voltage level or the same circuit can be worn in the same conduit, and the wires in the conduit are not allowed to have joints, nor are they allowed to have wires repaired after insulation damage.
(4) When laying the catheter, first remove the debris and water in the catheter; The line pipe laid in the tooling should be horizontal and straight, and can be supported by pipe clamps if necessary. When threading conduit, a 1.2 mm diameter conductor can be used as a lead.
(5) The iron wire should be firmly grounded and maintained at zero connection.
|
More on that
|
Inverter power and box structure selection - Reynolds
First, the selection of inverter power
The system power is equal to the product of the inverter power and the motor power, and the system power is higher only when both are operating at a higher power. From the perspective of power, when selecting the power of the inverter, we should pay attention to the following points:
1) ...
|
|
Reynolds soft starter fault code and fault handling
Reynolds soft starter fault code
Instantaneous stop -F 01 Instantaneous stop terminal 7 to terminal 10 open
TOO LONG STARTING TIME -F 02 STARTING TIME IS TOO LOW AND THE STARTING TIME IS TOO LONG (GREATER THAN 60S)
Overheating -F 03 Start too often, reduce the number of starts
Input out of phase -F 04 ...
|
|
Application misunderstandings and drawbacks of inverter and countermeasures - Reynolds
Misunderstanding: connect electromagnetic switches and electromagnetic contactors in the output circuit of the inverter
In actual use, some occasions require the use of contactors for frequency converter switching: such as when the frequency conversion is faulty, switch to the power frequency operation, or when the one-to-two method is adopted, a motor is faulty, and the variable frequency is used.
|
|
Wiring method and principle of PLC and inverter shielded wire - Reynolds
In order to avoid the interference of the control signal line between the PLC and the inverter by the space electromagnetic field, the shielding wire can be connected to the outer layer of these control signal lines to improve the anti-interference ability of the system. This kind of wiring must be noted, and only one point can be selected for the grounding point of the shield. Whether it's on the PLC side, or ...
|
|
Faulty inverter – Reynolds inverter
In ancient times, there were ten major tortures, which made people unable to survive and die, and experienced the purgatory of the world; Today, there are ten "tortures" of inverters, and the same can make your inverters suffer. Let's follow the editor to find out which of the top ten "tortures" will make your inverter "worse than dead"!
...
|
|
Reynolds inverter manual
Reynolds inverter brochure (partial)
Before installing
When unpacking, it is found that the machine has water or left water traces, indicating that the inverter has been flooded, so please do not install and use it.
When unpacking, it is found that the machine is damaged and deformed or the parts are missing, please do not install and use it, otherwise there will be fault expansion and personnel ...
|
|
Inverter maintenance power-on test instructions - Reynolds
First, the inverter is not repaired and the power test is tested
(1) Inverter repair test rectifier circuit
At the two ends of the inverter to detect the internal DC power supply, P and N ends, adjust the multimeter to the resistance RX10 gear, the red watch pen is connected to the P end, and the black watch pen is connected to R, S, T, and there are tens of ohms under normal conditions.
|
|
The Reynolds SVG series was successfully completed
More than 40 sets of RNSVG series low-voltage power generator sets and RNZB series high-voltage reactive power automatic compensation devices designed and produced by Reynolds have been successfully completed and will be delivered in the near future.
This product is owned by Shanghai Reynolds ...
|
|
Inverter frequency regulation fault solution - Reynolds
Most of the applications of frequency converters (hereinafter referred to as -VFDs) are primarily due to the fact that VFDs can change the output frequency and thus change the speed of the motor. If the frequency of the VFD cannot be adjusted and no damage is found on the hardware, it can be considered that the maximum output torque of the VFD is less than the load progress torque ...
|
|
Reynolds inverter control method
The actuator commonly used in the industrial field of Reynolds inverter has good speed regulation performance and simple and convenient operation method. Therefore, it is widely used in the automation system.
Typical wiring method for the main circuit of a Reynolds frequency converter
...
|
|
Precautions for installation of Reynolds low-voltage inverters
1. Safety precautions
1. The primary requirement is to have certain electrical professional knowledge, and understand the job site, understand the equipment status, and have certain electrical operation technology.
2. Determine the electrical ...
|
|
Interpretation of Reynolds inverter models
Take the RNB2000 series inverter as an example.
The model number of the RNB2000 series 37kW inverter is: RNB2037-U
RN: on behalf of Reynolds;
B: low-voltage frequency conversion governor;
2: 2000 series;
...
|
|
The basic principle of vector control – Reynolds frequency converters
The fundamental principle of vector control is to control the excitation current and torque current of the asynchronous motor according to the principle of magnetic field orientation through the measurement and control of the stator current vector of the asynchronous motor, and then to achieve the purpose of controlling the torque of the asynchronous motor. Specifically, it is to ...
|
|
Renault is available in a variety of product ranges
JJR1000系列：
JJR1011；JJR1017；JJR1022；JJR1030；JJR1037；JJR1045；JJR1055；JJR1075；JJR1090；JJR1115；JJR1132；JJR1160；JJR1200；JJR1250；JJR1320；JJR1400；JJR1500；JJR1600 ...
|
|
How to measure a frequency converter with a multimeter – Reynolds
How to use a multimeter to measure the quality of the inverter, it needs to be noted that for personal safety, it is necessary to ensure that the machine is powered off, and remove the inverter input power line R, S, T and output line U, V, W before operation! First of all, the multimeter is hit to the "secondary pipe" file, and then through the multimeter ...
|
|
The inverter protects the motor - Reynolds inverter
1. The output of the inverter for overvoltage maintenance has the function of voltage detection, and the inverter can actively adjust the output voltage, so that the motor does not bear the overvoltage, and the motor runs within the set voltage range.
2. Undervoltage maintenanceWhen the voltage of the motor is lower than 90% of the normal voltage (some are set to 85% ...
|
|
Wiring of the main circuit of the inverter - Reynolds
(1) Inverter three-phase communication input terminal (R, S, T)
The power input terminal is connected to the three-phase communication power supply through the circuit breaker of the circuit breaker for line protection, regardless of the connection phase sequence. It should be noted here that the three-phase communication power supply must not be directly connected to the inverter output ...
|
|
The inverter needs to rectify and then invert the cause - Reynolds
Special inverter suppliers remind you that in daily industrial production, there are inverters that do not require rectifier units, which are the so-called alternating current inverters. However, the vast majority of the market is AC-DC-AC frequency converter, which also contains a rectifier unit, which is a certain level of technology and market competition.
|
|
Characteristics and Discrimination of Resistance Damage - Reynolds
I often see many beginners tossing on the resistor when overhauling the circuit, and it is dismantling and welding, in fact, it is repaired a lot, as long as you understand the damage characteristics of the resistor, you don't have to bother.
Resistors are the most numerous in electrical equipment ...
|
|
The external configuration of the inverter is solved - Reynolds
With the improvement of the degree of automation of packaging machinery, packaging machine inverter (hereinafter referred to as VFD) plays an increasingly important role in packaging machinery. Capsule filling machine, high-speed tablet press, bottling production line, aluminum-plastic packaging machine, cartoning machine, each equipment will use VFD, mainly ...
|
|
Contact
working hours
