Buke servo motor - what is the impact on the operation of the servo motor of the fiber laser cutting machine?

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

1. The working principle of servo motor encoder It is a rotary sensor that converts rotational displacement into a series of digital pulse signals that can be used to control angular displacement, and can also be used to measure linear displacement if the encoder is combined with a gear bar or spiral screw. ...

1. Resistive touch screen The most important part of a resistive touchscreen is a resistive thin-film screen that matches the surface of the display very well. This is a multi-layer composite film based on a layer of glass or hard plastic plate, coated with a transparent metal oxide (ITO indium oxide, transparent conductive ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

1. The first difference between a servo encoder (synchronous service motor) and an ordinary encoder is that it provides sensing signal feedback for the commutation of the starting current. The main performance indicators of servo motor encoders are shift rate, accuracy, and repeatability. 1) Routinely mentioned 17-bit to 25-bit singleturn resolution ...

Buke touch screen programming software is a professional touch screen programming software, support for MT505T, MT506MV, MT508T, MT510T and other models, can assist users in the extreme time to grasp its planning methods, very suitable for modern industry increasingly large workload and function ...

1:11 alarm, control the power supply undervoltage, control the power inverter on P. The voltage between N is lower than the specified value. There are defects in the internal circuitry of the driver, etc. 2:12 alarm, control power supply overvoltage, control power inverter on P. N voltage exceeds the specified value, ...

In terms of the response speed of the servo drive: the torque mode has the smallest amount of calculation, and the driver responds the fastest to the control signal; The position mode is the most computationally intensive, and the driver is the slowest to respond to the control signal. When there are relatively high requirements for dynamic performance in motion, it is necessary to ...

1. Sweeping: Sweeping is generally caused by friction of the stator and rotor due to bearing damage, shaft bending, or improper assembly during maintenance. In the process of overhaul and assembly of the motor, the parts of the motor should be kept clean, and the assembly of the end cover, bearing, etc. should be reasonable and not barbaric construction, otherwise ...

(1) Encoder failure: It refers to the failure of the components of the encoder itself, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. (2) Encoder connection cable failure: the probability of this fault is the highest, and the maintenance ...

Since the new crown epidemic, the rapid growth of e-commerce has made the overall scale of China's express delivery industry grow rapidly, according to incomplete statistics, the business volume in 2020 has exceeded 80 billion pieces. Due to the growth of express delivery business volume, the automatic sorting efficiency of express delivery and parcels is becoming higher and higher.

The servo motor can control the speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. The rotor speed of the servo motor is controlled by the input signal, and can respond quickly, in the automatic control system, used as an actuator, and has an electromechanical time constant...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

1. Position proportional gain Set the proportional gain of the position ring adjuster; The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillation or overshoot; The parameter values are determined by the specific servo system type ...