KUKA robot control cabinet maintenance

Check if the robot is bumping and see if there is a mechanical load on the corresponding axes. See if the loading settings work. Whether the brake of the corresponding shaft is loosened. If the load component exceeds the additional scale, it is reduced to the constrained scale. Check the voltage input to the controller ...

1. It is necessary to check the equipment before starting, and the operation can be started only after confirming that the equipment is defective; 2. Check and sort out the operation place to ensure that there are no flammable materials (such as oil rags, waste oil gloves, paint, perfume, etc.) and no air leakage, water leakage; ...

1. Robot selection An industrial robot is a complex system, including manipulators, control systems, programmers and other software and accessories. Before use, it is necessary to select according to the actual production requirements of the enterprise and choose the products suitable for their own production line. Selected Guideline Packet ...

First, electrical connection Second, the initial power-on Third, security configuration Fourth, the robot zero point correction Fifth, I/O configuration seline; "> It is necessary to fix the robot before it can be powered on to operate the robot ...

1. Program control system: apply a certain rule of control to each degree of freedom, and the robot can complete the required space orbit. 2. Adaptive control system: when the external conditions change, in order to ensure the required quality or in order to improve the control with the accumulation of experience...

1. Working space and carrying ability: 1. The standard length of a single root of Cartesian coordinate type is 6m, and it can reach 100m after assembly; Combined into a gantry robot, its working space can be a very three-dimensional space. A single root can carry 10-200 kg, and the special structure can reach 2400 kg. ...

1) Run the CELL.src program in T1 or T2 form, perform part (1) in the figure, the KUKA robot performs back to the HOME point, performs the BCO operation, the window displays "BCO has been reached", and the BCO operation makes the KUKA robot run to the track. ...

KR CYBERTECH IS THE WORLD'S FIRST ROBOT BAR BAIER Engineering GmbH has developed the world's first fully automated bar with the help of a bar robot, which is in collaboration with the University of Aalen (Hochschule Aalen) and the beverage industry.

In order to complete high-quality and high-efficiency welding, it is necessary to promote advanced welding technology and welding automation technology in the manufacture of nuclear power equipment. The head of the nuclear power pressure vessel is composed of a hemispherical head intersected with a plurality of round pipes, and its weld groove is a J-shaped groove. Because of the limitation of the spatial location, the weld of the structure ...

1) In addition to aligning TCP (or using digital analogue), is there a way to improve the orbit accuracy? 2) There are cutting and other processes on site, which require high track accuracy, if the robot track presents the phenomenon formed by jitter such as sawtooth, how to deal with it? 3) ABB robot for ...

1: T1 mode, no program selection, the program start button is normal, and each axis of the robot reaches the position near the zero point; 2: Connect the EMD, the robot is X32; 3: Unscrew the lid with the tail of the device, and set the ...

1. Fulfill X-Start to enter the boot application, in the boot application, click Settings, and the network connection dialog box appears. 2. If you choose not to use the IP address, please click not to use the IP address of the robot drive, if ...

In the case of industrial robots and machine tools, it may involve the precise and harmonious movement of multiple axes in a specific space to complete the task at hand. Robots generally have 6 axes, and these axes must be harmonious and orderly, and if sometimes the robot moves along a trajectory, there will be 7 axes. ...

After each change to the motion command, the robot program must be tested at low speed (run method T1). Immediately starting a robot program at high speed can cause damage to the robot system and the entire equipment, as unpredictable movements may occur. If someone sits dangerously ...

In order to improve the welding attainability, the arc welding workstation usually uses a variety of positioners, and the common formforms of positioners include L-shaped positioners, tipping positioners, headstock positioners, etc. In the meantime, the L-type positioner and the tilting positioner have two external shafts, and some special working conditions require ...

Industrial robots are the star products of industrial automation, and the 30 billion ontology space is expected to leverage trillions of automation to transform shopping malls. The body space is about 30 billion yuan: the essence of automation is the automation of the process, and the ultimate policy is to improve the total factor yield. Multi-axis industrial robot is an automated ...

During the operation of the robot, if there is an urgent accident, the operation of the machine can be forcibly interrupted by stopping the equipment by external vertical stopping. 1. External emergency stop In case of emergency, how to quickly and accurately shut down the warehouse ...

Why does the robot flutter when it is running? Please do the following: 1. Is it that the load data you entered is incorrect? If the load data is too high or too low, and the difference between the load and the practice load is too large, it will cause flutter! 2、 ...

KUKA robot protective clothing is divided into a variety of types, different types have different functions, anti-static, dustproof, waterproof, etc. Here is a detailed introduction to the different types of robot protective clothing, different characteristics and protective functions provided by Hongsheng Decheng. ...

(1) Open the program Open the newly created program file banyunl" and enter the program editor. There are 4 lines of program in the program editor, in between, INI: initialization, END: program completion, and the middle two lines return to the HOME point. (2) Teaching: return to the HOME point Use...