The reason why the Estun welding robot teach pendant cannot enter the management interface

1. Check if the program starts normally, if not, update or reinstall. 2. Check if the robot operating system is working properly, upgrade or reinstall. 3. Check if the robot sensor or other connected equipment is working properly, if there is a problem, you can try ...

(1) Check the circuit condition (including the connection of power supply, controller, wiring and measuring instrument, etc.), check whether the spring of the starter is flexible and whether the contact is good. (2) When the constant voltage power supply is supplied, it needs to be started with a starter. Closed power switch, under motor load, ...

1. The control system has the function of input and output. Most of the welding robots are programmed offline, and the technicians write the welding program in advance, and then input the welding program into the control system, and the control system intelligently identifies the weld standard through the sensor, selects the appropriate welding parameters, and ...

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

1. Different ways of control Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. The workflow is different Stepper motor ...

Point 1: Whether the speed of the motor is normal, whether there is speed jitter and stall (can be checked with a tachometer). Point 2: Whether the anchor bolts of the motor are loose, whether the foundation is intact, and whether there are debris around. Point 3: Whether the housing and coupling of the motor are in good condition, ...

Features of Estun servo. 　　High overload capacity. The capacity of the industrial-grade intelligent power module IPM selected by the EDB/EDC servo drive is larger than that of similar servo products that are usually calibrated with the same power, and has the characteristics of strong overload capacity, strong anti-load disturbance ability, and large starting torque.

One: personal protection The safety operation procedures of welding robots are first of all to do a good job of personal protection, and the maximum scale of welding robot operations is set up outside the protective fence or cordon, and personnel are not allowed to enter the scale of their operations in the welding robot operation. In the process of welding robot operation, it is necessary to ...

First, the control accuracy is different The step angle of the two-phase hybrid stepper motor is generally 3.6 ° and 1.8 °, and the step angle of the five-phase hybrid stepper motor is generally 0.72 ° and 0.36 °. There are also some high-performance stepper motors with smaller step angles. Such as Sitong company produced a kind of wire for slow wire ...

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

Servo motor refers to the engine that controls the operation of mechanical components in the servo system, and is a kind of auxiliary motor indirect transmission device. The main function is to use it in a closed ring, transmit the signal to the system at any time, and at the same time correct its own operation with the signal given by the system. Servo motor ...

1. Will the servo motor lose steps or walk inaccurately? The servo motor is controlled in a closed loop by the driver through the feedback of the encoder. After receiving each pulse command, the driver drives the motor to rotate at an angle, and checks whether the motor is rotated to a given point by the encoder

Speed regulation of DC motors Constant power weak magnetic upward speed regulation, the magnetic field governor can be adjusted until the speed reaches the required value, but shall not exceed the maximum speed allowed by the technical conditions. Constant torque loads can be slowed down by step-down or armature string resistors. Downtime of the DC motor ...

The 2021 China International Medical Equipment Fair will be held from May 13 to 16 at the National Convention and Exhibition Center in Shanghai. Estun Medical will exhibit the unilateral and bilateral versions of the Burt Upper Limb Rehabilitation Training System, which is more suitable for the full-cycle rehabilitation training program of the rehabilitation population, and includes adaptation ...

7. The relationship between the model code parameters and the servo motor The motor model in the model code parameter of the EDB series servo motor should be the motor model currently controlled, otherwise the operation effect of the motor will be poor. The motor model selection parameter is PN218, and the drive model parameter selection is PN ...

On June 17, 2021, at the same time of the 25th Essen Welding Exhibition, Estun Automation and its wholly-owned subsidiary CLOOS released a number of new welding robots and new welding power supplies in Shanghai. ESTUN Weld Automation Set EWAS series welding robots EWAS ...

1. Open the robot control software: use the computer to connect the robot, start the control software, and enter the robot control interface. 2. Select the point mode: select the point mode in the control interface, in the point mode, the robot will record and execute the point set by the user. ...

(1) The motor heat dissipation system is faulty The temperature of the motor rises due to the heat generated by the motor not being dissipated quickly. At this time, the main solution is to check whether the cooling fan of the motor is operating normally and whether the direction of rotation of the fan is correct. The surface of the motor is ...

A51: The robot spindle servo motor is abnormal. It could be a cable failure, a servo drive problem, a damaged spindle bearing, etc. A47: The servo motor is overheating. It may be because the external ambient temperature is too high, the servo motor is starting to break, and it cannot be cooled properly. A4 ...

1. Problems in the application of industrial robot palletizing Palletizing gripper problems The ability of the palletizing robot to work under different operational tasks mainly depends on the design of the robot flange crane. The quality and performance of the robot crane directly affects the work of the industrial handling robot ...