Estun robot prompts "The program is not in a stopped or paused state, and the program failed to start!" ”

1. The working principle of incremental encoder: The incremental encoder converts the displacement into a periodic electrical signal, and then converts the electrical signal into a counting pulse, and the number of pulses indicates the size of the displacement. To describe the pouring water, the incremental encoder is like, looking for a non...

Common system failures during the welding process 1. Collision of guns: It may be due to the error of workpiece assembly or the inaccuracy of the TCP of the welding gun, you can check the assembly situation or correct the TCP of the welding gun. 2. Arc fault, unable to start the arc: it may be due to the fact that the welding wire does not contact the workpiece or ...

Features of Estun servo. 　　High overload capacity. The capacity of the industrial-grade intelligent power module IPM selected by the EDB/EDC servo drive is larger than that of similar servo products that are usually calibrated with the same power, and has the characteristics of strong overload capacity, strong anti-load disturbance ability, and large starting torque.

1. What is "inertia matching"? 1. According to Newton's second law: "The required moment T of the feed system = the transmission inertia of the system J×angular acceleration θ angle". The acceleration θ affects the dynamic characteristics of the system, the smaller θ, the more time from the controller to the completion of the system's execution.

First, the control accuracy is different The step angle of the two-phase hybrid stepper motor is generally 3.6 ° and 1.8 °, and the step angle of the five-phase hybrid stepper motor is generally 0.72 ° and 0.36 °. There are also some high-performance stepper motors with smaller step angles. Such as Sitong company produced a kind of wire for slow wire ...

Special attention should be paid to the following matters when the motor is regularly inspected during use: 1. The area around the motor should be kept dry, and no other objects should be placed inside and outside it The cleaning of the motor shall not be less than once a month, and the dust inside shall be blown off with compressed air during cleaning.

Alarm code A04 refers to: Alarm mechanism: The overload rate of the drive accumulates to a certain threshold and triggers an alarm. Causes: 1. Servo motor brake control circuit problem; 2. Robot power cable problem; 3. The drive parameter setting is wrong; ...

Problem 1: The reason why the servo motor alarms the overload If the drive resistance is too great, check the drive system. Q2: What is the difference between stepper motor and servo motor overload capacity? Question 3: Is the servo motor overload necessarily related to the current? As the motor torque output ...

Advantages and disadvantages of AC servo motors Advantages: good speed control characteristics, smooth control over the entire speed zone, almost no oscillation, high efficiency of more than 90%, less heat generation, high-speed control, high accuracy position control (depending on encoder accuracy), rated operating area ...

1. Q: What are the precautions for the selection of incremental rotary encoders? There are three parameters that should be noted: 1. Mechanical installation dimensions, including positioning stops, shaft diameters, and mounting holes; cable outlet mode; installation space volume; Whether the protection level of the working environment meets the requirements. ...

1. Fault phenomenon: The uneven distribution of the magnetic field of the ions, the unbalanced three-phase current aggravates the vibration and noise of the motor during operation, and the motor cannot be started when it is serious, and a large short-circuit current is generated in the short-circuit coil, which causes the coil to heat up rapidly and burn out. 2. Causes: ...

CALIB Command: This instruction calibrates joint position sensors. STATUS command: Used to display the status of the user's program. FREE command: This command displays the unused storage capacity. ENABL command: used to turn the system hardware on and off. ZERO Directive: This directive ...

Troubleshooting and Detection Causes of Estun Controller: 1。 The servo amplifier is based on the effective value of the output torque 2. Calculate the load factor. If the value exceeds PR5 12, protection is generated. 3. From the amplifier front panel above the "D15. ol' monitoring mode or panatermm...

Common faults of Estun servo drives 1. The LED light is green, but the motor does not move Reason 1: Motors in one or more directions stop the action. Solution: Check the +INHIBIT and -INHIBIT ports. Reason 2: The command signal is not on the driver ...

1. Estun servo motor maintenance - overload alarm A04 1. The wiring of the servo motor is wrong or the wiring is leaking (1) The U, V, and W phase wires of the motor are connected incorrectly (2) Whether the insertion of the connector on the servo motor side is defective 2. The model of the servo drive and the motor does not match ...

1. Amplitude and phase control mode The amplitude and phase are controlled, and the speed of the servo motor is controlled by changing the amplitude of the control voltage and the phase difference between the control voltage and the excitation voltage. That is, the amplitude and phase of the control voltage UC are changed at the same time. 2. Phase control mode Phase-controlled ...

1. Open the shell of the robot to expose the motor base. 2. Use a screwdriver or wrench to remove the screws on the motor base. 3. Remove the screws, lift the motor base, and disassemble it from the robot. 4. The motor base is tightly connected with the robot, and tools such as wrenches are used.

On March 11, Nanjing Estun Automation Co., Ltd. (hereinafter referred to as Estun) and Beijing Machinery Industry Automation Research Institute Co., Ltd. (hereinafter referred to as Beijing Institute of Automation) joined forces and reached a strategic cooperation agreement. Wang Zhenlin, Secretary of the Party Committee and Chairman of the Beijing Autonomous Institute, Estun Automatic ...

Servo drive is a kind of controller used to control servo motor, its role is similar to the inverter to ordinary AC motor, as a precision equipment, it will inevitably have some faults in the process of use, common faults and maintenance methods are as follows: 1. When the motor rotates, the LED light ...

1. Position mode Look at this name, you can guess a rough idea, to put it bluntly, the position requirements are relatively high, such as the linear servo module this kind of mechanism, the need for the sliding mechanism to stop accurately, just use this mode, speaking of which, let's take a look at the ball screw module ...