Introduction of OTC robot detection and deburring system

Find an operation origin for the OTC welding robot: click "Program" on the teaching pendant, enter 9999, press "Acknowledge", press "Trek View", and the current process will flash yellow on the teaching pendant. OTC Welding Robot Programming Process Tutorial Step 2: Create an empty program ...

Robot is a very complex system, there are many planning challenges in mechatronics, functionality and electrical, when planning the building blocks of the robot system, it is necessary to understand the needs of these aspects and select appropriate planning ideas. ...

OTC welding robots*** are commonly used in 4 types: FD-B6, FD-B6L, FD-V8, FD-V8L. From the name, it can be seen that FD-B6 and FDB6L belong to one category, and FD-V8 and FD-V8L belong to one category. The numbers in these four types of designations represent their loads ...

Welding is a very demanding operation in industrial production, and novices who are new to welding will feel confused by all kinds of new terms. If you want to do a good job, you must first sharpen your tools. If you want to quickly get started with the welding profession, you must grasp the basic knowledge of welding. Share a ...

The process measures to reduce the welding stress and deformation of welding robots mainly include: 1. Heating "subtraction zone" method Before welding, the welding robot is heated in the area near the welding part (subtraction area) to make it elongated, and when it is cooled after welding, the heating zone is shortened together with the weld.

This article first introduces the OTC robot repair case - the calibration method and process of the teach pendant touch screen (W-L02140). When we use the OTC robot teach pendant, we adjust the touch screen light spot and the process of screen echoing.

1. Find the operation origin of the OTC welding robot: click "Program" on the setting box, enter 9999, press "Confirm", press "Look Forward", and the yellow displayed on the setting box is the current process. 2. Create an empty ...

Splash issues Because metal is thrown from the weld point to adjacent surfaces, spatter reduces power and adds expense to the installation line. After the welding is completed, the welder needs to sort out the weld, and the rest of the data is wasted. Many welders think it's part of welding. Many people learn ...

1. Adjust the arc voltage If the settings are incorrect, the voltage setting will significantly add to the spatter. The low voltage setting can cause spatter as the wire is repeatedly short-circuited in the weld pool, resulting in a small burst at the wire tip. This short circuit is normal for short arc MIG welding, but ...

In order to make the welding robot work efficiently and ensure the normal operation of the robot, the user needs to regularly maintain and check the robot body and system after using the robot to a predetermined time. Together to ensure the safety of equipment and personnel during operation, the robot operates every 4000 hours.

1. The axis key that controls the movement of the junction is mainly used to adjust the orientation and angle of the robot and the welder. When the SW switch is pressed, the cooperative coordinates can be used to control the robot's orientation. 2. The coordinate switching button can be used to cut between axis coordinates, robot coordinates and tool coordinates.

1. Preparation before robot maintenance 1. Robot oil type: REO about 1000ml, EP2 about 10-30ml, WR2 about 10ml 2. Tools: one technical refueling pump, 4 syringes, oil blotting paper, several plastic bags, waste oil drums, hexagonal wrenches 3. Robot ...

The difference between robotic palletizing and depalletizing is that they perform different tasks. Palletizing is the safe stacking of objects together, while destacking is the unpacking of previously stacked objects. Both of these features can improve the output power and reduce the manpower input, and together they also reduce the operational risk and ...

The OTC robot needs to adjust the tension of the belt once a year or every 3,000 hours of work, whichever is shorter. The OTC robot B4 (B4L) is used as an example to introduce the adjustment method and precautions. The timing belt of the OTC robot B4\B4L is located in the motor and reduction gear.

Replace the battery with a low voltage when the power is not interrupted. After that, the origin of each axis is reset. 1. Align the corner marks of each axis of the robot so that each axis of the robot stops at the origin position. If the servo cannot be powered on, ...

1. Keep the surface of the palletizing robot clean and clean up the dust in time; 2. Check whether the fixing bolts of the palletizing robot are loose once a week; 3. Smooth the cylinder support shaft, hinch seat hole and shaft every day. 1-2 drops of smooth oil per filling; ...

Industrial robots need a precise and simple end actuator that can handle many different parts, and it is necessary to know what type of parts will be processed before selecting the gripper of the industrial robot. 1) Shape Asymmetrical, tubular, spherical and tapered ...

Abort means that during the operation of the computer, when there are some unexpected situations that require the intervention of the host, the machine can actively abort the running program and transfer to the program that deals with the new situation, and then return to the original suspended program to continue to run after processing. ...

OTC welding robot as a widely used advanced automatic welding equipment, has the characteristics of high versatility and stable action, to use the robot to complete the welding task, the engineer only needs to teach the robot once to correctly reproduce the operation of the teaching process. Let the robot do the rest ...

1. The structure of the conveyor belt feeding at the front end of the claw of the palletizing robot, the roller conveyor belt for bag grabbing generally has a national standard, and the standard interface needs to be selected, and how to complete the belt conveyor belt should be considered. 2. The selection of the palletizing robot model, the robot load can be ...