When using touch screens, due to technical limitations and poor environmental adaptability, especially surface acoustic wave screens. The screen cannot be used normally due to water droplets, dust, etc., so touching the screen requires regular maintenance just like ordinary machines. And since the touch screen is much ...

At present, the development of touch screen technology shows the following trends: 1. The flexibility of the screen will be better and the clarity will be further improved People have higher and higher requirements for touch screens, from low resolution to high resolution, from poor light transmittance to good light transmittance. United States E-Ink ...

1. Connect the touch screen with the PLC We know the communication between two pieces of hardware, whether wireless or wired. The first step is to establish a connection. The most common connection between PLC and touch screen is serial data cable connection. The data cable can be used in a treasure ...

1. The film surface of the touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product 2. The touch screen part is a glass product, the corners of the glass are sharp, please wear gloves/finger sleeves when assembling 3. The touch screen part is a fragile glass product, and it should not be touched during assembly.

1. The inverter burns out 2. The fuse will be burned when the power is on, and the motherboard will fail; 3. The liquid crystal is faulty, and the motherboard is also burned; 4. The power supply of the motherboard is partially damaged; 5. The motherboard is faulty, and there is a large current burnout; 6. The backlight does not light up, and the motherboard inverter is faulty; 7. Reverse ...

When the system setting password of Verun Tong touch screen hardware is lost, the factory settings can be restored by the system initialization method. There are four ways to enter the touch calibration of the touch screen of Veruntong, and the initialization of the operating system can only be carried out through the DIP switch. 1. DIP switch mode touch calibration ...

When using the Weiluntong touch screen, how to set the IP address Examples: CMT2109X2 and CMT2079X First of all -> click on the little yellow button on the touch screen Secondly -> Click on the lock symbol Again-> Enter the password by default 111111 And then-〉 ...

1. The download password does not match the hardware download password. 2.USB download cable contact**. 3. USB on PC does not support USB2.0. 4. The touch screen USB interface is burned out. 5. Recently, the touch screen has been reset but the upload and download password has not been reset. ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power back on, a white crosshairs will appear on the screen, click the middle of the crosshairs vertically, after the point (the time can not be too short), the crosshairs will automatically jump to the next position, crosshairs ...

Sometimes we need to monitor and change the program of PLC equipment, and when it is inconvenient to connect to PLC or there is no communication line, we can choose to achieve it through the penetration function of the touch screen. The traversal communication function consists of the following two modes: Ethernet When using [Ethernet] ...

overview The BCD format is a binary-encoded decimal, commonly known as 8421 codes Hex is the hexadecimal system Binary is the denoting binary Elaborate: 16-bit BCD: Single-word, BCD format 32-bit BCD: Two-word, BC ...

First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the surface of the touch screen for dirt and dirt.

1. The memory address is different. The memory address of the PW touch screen uses the local hold register, while the memory address of the RW uses the hold register index to send RWI. 2. The address range is different. The address range of the LW of the touch screen is 0 to 524287, while the address range of the RW is 0 to .

1. Enter the Weiluntong touch screen setting interface, find the input method option, and change it to the corresponding text type (such as Chinese Simplified, English) to solve the problem. 2. Install the corresponding input method, which can also solve this problem. ...

1. Software editing-system parameter setting-HMI attributes-port number: 8000 change, such as 9000; 2. Bring up the computer task manager - end com_e30.exe under the process; 3. Restart the computer; 4. Query other occupancy on the computer through TCPview software.

1. Open the Weiluntong editing software, and click Event Login in the pop-up menu bar on the right. 2. On the edit page of event login, we click the new button below, and then a setting page for alarm login will pop up.

1. First of all, open the Weiluntong touch screen and enter the application. 2. Secondly, select "Edit" → "Personalization" on the control bar of the window. 3. Finally, set the picture to the bottom layer. ...

1. After selecting the PLC first, click "Import Label". 2. Next, browse - select the variable label exported from the PLC programming software - open. 3. Click "Import" and select "Yes" in the Retention Label dialog box. 4. Finally, the verification label is executed. ...

1. Add what you need as a picture to the picture library. 2. Create animations with animation tools. 3. There is a (upper right) button in the toolbar of Weilun Tong programming software, that is, the animation button, click on the 3 tracks of the animation movement on the program drawing interface and then right-click, you can ...