How to set the IP address of the touch screen on the touch screen

1. The download password does not match the hardware download password. 2.USB download cable contact**. 3. USB on PC does not support USB2.0. 4. The touch screen USB interface is burned out. 5. Recently, the touch screen has been reset but the upload and download password has not been reset. ...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

1. Surface acoustic waves are not interfering with other electronic devices. Because only the superficial surface of the screen has ultrasonic waves with a frequency of 5MHz, there will be no interference with other electronic devices. 2. The length of the serial port cable (touch screen to PC). The serial cable can theoretically reach a transmission distance of 15M, ...

The human-machine interface is not just a simple operation screen, but more and more integrated into new functional elements such as network technology, remote control, video input, etc., and has gradually evolved into a networked information control platform integrating display, monitoring, communication and operation. And in this wave of innovation ...

(1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when correcting the position. Solution 1: Recalibrate the position. Phenomenon...

EasyBuilder Pro is a very easy to use and powerful Veruntong touch screen programming software, the software provides a humanized human-computer interaction interface, which can meet the needs of different programmers, suitable for Veruntong eMT, cMT, iE, MT (iP) and TK (iP) models, the software provides ...

1. Why can't the screen display Chinese normally, but the display is garbled? Answer: This situation is generally caused by not choosing the correct Chinese font, just choose a Chinese font, the specific operation steps are as follows: 1) In EasyBuilder soft...

cMT3151 can be stored in the form of data streaming, avoiding the SD card or USB when storing data due to falling off and unable to produce a complete storage record; At the same time, the abnormal operation of the machine is recorded, and the user is assisted in tracking and analyzing the source of the problem. cMT-iPC15 Built-in Error Correction Code (ECC) ...

1. Software editing-system parameter setting-HMI attributes-port number: 8000 change, such as 9000; 2. Bring up the computer task manager - end com_e30.exe under the process; 3. Restart the computer; 4. Query other occupancy on the computer through TCPview software.

1、MT6102iQ 10.1" TFT display 1024*600 dots, brightness 350, contrast ratio 500:1, 16.7M color, 128MB memory, DC10.5-28VDC power supply, four-wire resistive type, USB Host USB2.0/Serial Interface (Con.A COM2 RS-485 2W/...

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

1. The infrared touch screen does not need touch pressure, it can be operated freely even if you wear gloves, and anything can be touched. 2. Compared with the display equipped with capacitive and resistive touch screen, the picture saturation is richer and the contrast ratio is better, which improves the user's visual comfort. ...

25. Bit status switch switch, bit status indicator, equipment linkage: Through the bit state switching switch element OFF->ON, the macro command is executed: the bit status indicator is set to the ON state; Select the execution macro through the PLC control, select the trigger mode ON->OFF, and set the bit ...

overview The BCD format is a binary-encoded decimal, commonly known as 8421 codes Hex is the hexadecimal system Binary is the denoting binary Elaborate: 16-bit BCD: Single-word, BCD format 32-bit BCD: Two-word, BC ...

The five-wire resistive touch screen and the four-wire resistive touch screen both adopt the principle of analog resistance, and their conventional fault characteristics are exactly the same as those of the four-wire resistor. If you are using a five-wire resistive touch screen, when there is an installation and maintenance problem, please determine and solve the problem in the following order. ...

1. Connect the touch screen with the PLC We know the communication between two pieces of hardware, whether wireless or wired. The first step is to establish a connection. The most common connection between PLC and touch screen is serial data cable connection. The data cable can be used in a treasure ...

Transparent properties Transparency, which directly affects the visual effect of the touch screen. Transparency has the problem of transparency, infrared technology touch screen and surface acoustic wave touch screen are only separated by a layer of pure glass, transparent can be regarded as a leader, other touch screens should be carefully scrutinized, "transparent", ...

1. Copy the required OS to a USB flash drive (FAT32 format is only supported); For example, in the next test, place the OS file in the firmware folder at the root of the USB flash drive. 2. Plug the USB flash drive into the USB host port of the HMI to be updated; 3. Click the arrow in the bottom right corner of the screen ...

When the HMI communication failure is caused by on-site interference, the following methods can be used to troubleshoot the fault: The communication line adopts shielded twisted pair cable, and the shielding layer needs to be grounded at one end, that is, only one end of the PLC and the touch screen can connect the shielding layer to the ground horn (it is recommended to connect it to the HMI end of the touch screen) ...

1. Touch failure; 2. Touch the glass plate is broken; 3. The key is damaged and the key is not effective; 4. White vertical bars, horizontal bars, and bright lines appear; 5. Half can be touched, half can not be touched; 6. Can't enter the program; 7. The touch screen cannot be calibrated.