1. DIP switch mode touch calibration and system initialization. For the full eMT series, MT8000i series, TK series, WT series and other HMIs, there is a set of reset buttons and DIP switches, which can trigger the corresponding functions when switching between different modes. If the HMI touches ...

1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4W represents the wiring method, that is, the four-wire ...

Key points of Weiluntong touch screen selection: 1. Consider the size, how big the screen is, 7 inches or 10 inches, etc 2. Whether there is an Ethernet communication interface or a USB interface 3. Consider the type of interface supported by the touch screen, RS232/RS485 interface 4. Whether it has ...

1. Check that the power cord is plugged in and if there is electricity. If there is no electricity, you can replace the cord or plug. 2. Check if the power switch is on. If it doesn't turn on, you can try turning on the power switch. 3. Check if the battery is charged. If the battery is low ...

1. Locate the relevant property. In the property settings of the touch screen, find the properties that need to be set, such as touch screen input, output, communication and other related attributes. 2. Set the properties. Set the appropriate property values as needed. If some properties don't have predefined options, ...

1. Open the touch screen of Weiluntong, click "Alarm Information" on the left menu bar, and enter the "Alarm Information Management" interface; 2. In this interface, you can see all the current alarm records, click "Function", select "Clear All Alarms", you can clear all historical reports.

1. Software use issues 1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4 ...

There are 2-4 hidden DIP switches on the back of the VIRONT touch screen, and each HMI backplate has a set of reset buttons and DIP switches that can be used to trigger the corresponding function when switching between different modes. The following is a list of categories: mTV series 　　cMT-SVR series 　　If cMT-SVR ...

The Ethernet IP address and port number are set on the touch screen, such as 192.168.10.11, port number 102, and other parameters are set by default, that is, after setting the system parameters, you can edit the screen.

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power on again, a white cross cursor will appear on the screen, click the middle of the cross cursor vertically, after the point (the time can not be too short), the cross cursor will automatically jump to the next position, the cross light ...

1. Press the "Menu" button to enter the menu interface. 2. Select the "Picture" option to enter the screen settings interface. 3. In the screen settings interface, find the "Copy" option and press the "Enter" key to enter. 4. In the "Copy" option, select "Copy...

1. Check the user manual or technical manual of the touch screen to understand the menu settings and operation methods of the touch screen of this model. 2. Try pressing other buttons or areas on the touchscreen to see if you can enter the menu settings interface. 3. If you are using third-party software or ...

Weilun Tong macro is a programming language for human-computer interface interaction development, which is based on a programming language developed by Microsoft in the early VB, macro provides EBPro application outside of some additional functions you need, macro is widely used, almost PLC control ...

1. First of all, open the Weilun touch screen to modify the software, and be sure to choose the software corresponding to the type of touch screen; 2. Modify the required touch screen screen; 3. Then open the "System Settings" button under the "Common" menu in the upper left corner; 4. Set the pop-up window in the system ...

1. First of all, open the created Weilun touch screen project, select Common in the menu bar and click Open. 2. Secondly, select the system parameter icon in the common drop-down menu and click to open. 3. Finally, click Change. ...

1. Enter the system settings interface of the Weilun touch screen, and select the "Power Management" option in the "System Settings". 2. In "Power Management", you can set how long the touch screen will automatically enter the "standby" state without operation, and you can also set how long it will enter the "...

1. Appearance of Weiluntong contact screen: Use special Weiluntong contact screen cleaner and soft fiber cloth to clean the appearance of Weiluntong contact screen, remove dirt and fingerprints, etc., to ensure a clean appearance. 2. Restart the device: test to restart the contact screen device of Weiluntong, sometimes restart...

1. Check the appearance of the touch screen: Observe whether there is dirt, fingerprints or scratches on the surface of the touch screen, which may affect the sensitivity and accuracy of the contact. Use a soft cloth or a special Velonton touch screen cleaner for cleaning. 2. Closed other applications: fake ...

1. Create a new device driver: Enter the IP of the PLC. 2. Create a new PLC variable from Siemens. 3. Create a new button and download it to the touch screen.

To change the IP address of the touchscreen, you need to click the arrow below the touchscreen. Then enter the original password of the touch screen in the pop-up interface: 111111. After that, enter the IP setting interface. Enter the interface to set the IP address you want to set, and finally remember to click after setting ...