How does the touch screen of Weiluntong put the picture at the bottom layer

When the HMI communication failure is caused by on-site interference, the following methods can be used to troubleshoot the fault: The communication line adopts shielded twisted pair cable, and the shielding layer needs to be grounded at one end, that is, only one end of the PLC and the touch screen can connect the shielding layer to the ground horn (it is recommended to connect it to the HMI end of the touch screen) ...

1. SPI interface Serial Peripheral Interface (SPI): Serial peripheral interface. It was first defined by Motorola on its MC68HCXX series of processors. It enables the MCU to communicate serially with various peripherals to exchange information. The SPI has three registers ...

The Ethernet IP address and port number are set on the touch screen, such as 192.168.10.11, port number 102, and other parameters are set by default, that is, after setting the system parameters, you can edit the screen.

1. Press the "Menu" button to enter the menu interface. 2. Select the "Picture" option to enter the screen settings interface. 3. In the screen settings interface, find the "Copy" option and press the "Enter" key to enter. 4. In the "Copy" option, select "Copy...

1. Do not hit with metal objects. Usually the HMI will be covered with a layer of glass to protect the screen and make it easy to touch. However, the glass is fragile, do not hit the screen with metal objects during use, it is easy to cause the glass to be scratched or broken. 2. Avoid squeezing the screen with heavy objects. Around HMI ...

1. TK series (simple and practical, widely used) 1、TK8071iP 7" TFT display 800*480 dots, brightness 350, contrast ratio 500:1, 16M color, 128MB memory, DC10.5——28VDC power supply, four-wire resistive type, overall dimensions 200.4*146.5*34m...

1. If you are using a capacitive touch screen, then it is recommended that you first install the driver required for the capacitive touch screen correctly according to the requirements of the manual when you use it for the first time, and then click "Start"/"Program"/"Microtouch Touc" on the screen with your fingers.

1. Locate the relevant property. In the property settings of the touch screen, find the properties that need to be set, such as touch screen input, output, communication and other related attributes. 2. Set the properties. Set the appropriate property values as needed. If some properties don't have predefined options, ...

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

18. Macro calculation: The values to be calculated are read, and then the data is calculated and written to LW0. 19. According to the different selections of the project menu, two different direct windows will pop up with one button: Macro commands are triggered by a button to read the ...

EasyBuilder Pro is a very easy to use and powerful Veruntong touch screen programming software, the software provides a humanized human-computer interaction interface, which can meet the needs of different programmers, suitable for Veruntong eMT, cMT, iE, MT (iP) and TK (iP) models, the software provides ...

First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the surface of the touch screen for dirt and dirt.

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

When the touch function of the touch screen fails, first try to enter offline mode to verify whether the touch screen backlight is burned out. If the cause of the fault is verified to be a burned-out backlight, then we can follow the steps below to temporarily restore the touch function of the touchscreen (take the Proface GP series touchscreen as an example below).

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

Why can't the infrared touch all-in-one machine be calibrated? 1. It is possible that the touch screen control card receives the operation signal before the host starts to load the touch screen driver, please power off and restart the computer and recalibrate. 2. It is possible that the sound wave screen is used for a period of time, ...

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power back on, a white crosshairs will appear on the screen, click the middle of the crosshairs vertically, after the point (the time can not be too short), the crosshairs will automatically jump to the next position, crosshairs ...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

(1) FILM - that is, the film used for touch, the base material is PET. When touched, the ITO of the upper and lower layers is brought into contact by deforming the film, resulting in different "resistance values" in the X and Y axes (similar to the principle of moving rheostats). Depending on the requirements of use, the table of FILM ...