How to realize the automatic pop-up alarm page on the touch screen of Weiluntong

1. Dispose of dirt and grease on the touch screen The accuracy of the screen is a characteristic of grease build-up on the surface, which can make it cumbersome to type the correct commands. In addition, due to the accumulation of dust caused by overheating, the internal components of industrial computers may not work properly. The use of microfiber ...

1. The touch all-in-one machine can carry out the dynamic display of the three-dimensional model of the object, and has a good interactive experience function. The audience can operate by themselves through the touch all-in-one machine, and "touch" the object at zero distance on the screen, and the audience can also rotate and zoom in arbitrarily on the touch all-in-one screen.

1、cMT3090 9.7" TFT display 1024*768 dots, brightness 350, contrast ratio 500:1, 262K color, Flash memory: 4GB memory, 1GB, DC19.2-28.8VDC power supply, four-wire resistive type, SD card slot, support SD/SDHC, USB Host USB ...

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. There are generally three ways to enter the system setting of the TK6070ih touch screen: 1,Generally in the lower right corner of the touch screen, ...

1: For new projects, choose Weiluntong touch screen models; 2. Select the device in the system parameter settings and click Add Device/Server; 3. Go to the new device/server, select OMRON Corporation, and confirm; Four: Enter OMRON Corporation, select ...

1. The inverter burns out 2. The fuse will be burned when the power is on, and the motherboard will fail; 3. The liquid crystal is faulty, and the motherboard is also burned; 4. The power supply of the motherboard is partially damaged; 5. The motherboard is faulty, and there is a large current burnout; 6. The backlight does not light up, and the motherboard inverter is faulty; 7. Reverse ...

1. Observational method As the name suggests, it is to use the eyes to visually check whether the components are burned, damaged, deformed, discolored, cracked, and whether the CRT filament is lit after the current is turned on.

Open the Veriton touch screen programming software, select [Common] in the main interface and open it In the Common drop-down menu, select System Parameters and click Open. Then select [HMI Attributes] in the pop-up system parameter setting menu and click OK. ...

1. When turning on and off the power of the machine, it should be operated in strict accordance with the regulations; 2. According to the severity of the environment, set a time limit to open the machine head to clean the reflective stripes and inner surface of the touch screen; 3. At present, the mainstream industrial display program does not have a mouse cursor, because the flashing of the cursor will ...

[Fault Analysis and Processing] First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the touch ...

Since the launch of the cMT-SVR, the innovative body and screen separation architecture has subverted the market's imagination of HMI. With the continuous cultivation of Weiluntong, this unique detached HMI has gradually gained a foothold in the market and is now widely used in the market. 　　In order to meet the needs of the new generation of industrial Internet of Things ...

The parameters of the touch screen to characterize the characteristics of the capacitor include the loss factor D value, the figure of merit Q, the series equivalent resistance ESR, etc., the essence is the same, take a parameter to know the quality of the capacitor, but take the loss factor D value reference meaning. These parameters are usually not possible with a digital bridge.

2.1 Why is the year display on the touchscreen 606 instead of 2006? This is because the orientation of the high and low bytes of the words in some PLCs is not the same as that of general PLCs, such as Siemens PLC, so in this case, you only need to manually enter the 2006 year from scratch on the screen.

When the system setting password of Verun Tong touch screen hardware is lost, the factory settings can be restored by the system initialization method. There are four ways to enter the touch calibration of the touch screen of Veruntong, and the initialization of the operating system can only be carried out through the DIP switch. 1. DIP switch mode touch calibration ...

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

On November 7, 2017, the five-day 2017 China International Industry Fair (hereinafter referred to as the "Industry Fair") opened at the National Convention and Exhibition Center in Shanghai. As Asia's largest and brand's top event in the field of industrial automation, this event brings together the world's leading automation equipment manufacturers.

1. Enter the Weiluntong touch screen setting interface, find the input method option, and change it to the corresponding text type (such as Chinese Simplified, English) to solve the problem. 2. Install the corresponding input method, which can also solve this problem. ...

1. Background color: Right-click on the blank space of the window, select Properties, Pop-up Settings, and select a color in the background; Hatch: In the background, tick the fill, select the pattern color and pattern. 2. Picture/Background Image: Select Picture Element ...

Weilun Tong macro is a programming language for human-computer interface interaction development, which is based on a programming language developed by Microsoft in the early VB, macro provides EBPro application outside of some additional functions you need, macro is widely used, almost PLC control ...