Steps to restore the factory settings of the Verun Tong touch screen

The default standby time is 1 minute. The specific steps are as follows: 1. First of all, open our touch screen editing software, and be sure to select the software corresponding to the touch screen model. 2. Edit the touch screen screen we need. 3. Open the common menu in the upper left corner ...

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power on again, a white cross cursor will appear on the screen, click the middle of the cross cursor vertically, after the point (the time can not be too short), the cross cursor will automatically jump to the next position, the cross light ...

To change the IP address of the touchscreen, you need to click the arrow below the touchscreen. Then enter the original password of the touch screen in the pop-up interface: 111111. After that, enter the IP setting interface. Enter the interface to set the IP address you want to set, and finally remember to click after setting ...

1. First of all, open the created Weilun touch screen project, select Common in the menu bar and click Open. 2. Secondly, select the system parameter icon in the common drop-down menu and click to open. 3. Finally, click Change. ...

1. The power cord is not properly connected This may seem obvious, but make sure the power cord is connected to the back of the touchscreen and plugged into a power outlet. If it looks like it's connected correctly, disconnect and reconnect both ends of the power cord to make sure the cable isn't loose. 2. The power cord is damaged ...

1. The film surface of the touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product 2. The touch screen part is a glass product, the corners of the glass are sharp, please wear gloves/finger sleeves when assembling 3. The touch screen part is a fragile glass product, and it should not be touched during assembly.

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

1. If you are using a capacitive touch screen, then it is recommended that you first install the driver required for the capacitive touch screen correctly according to the requirements of the manual when you use it for the first time, and then click "Start"/"Program"/"Microtouch Touc" on the screen with your fingers.

Advantages of infrared touch screen: 1. High stability, will not drift due to changes in time and environment 2. Highly adaptable, not subject to current, voltage and static interference, suitable for some harsh environmental conditions (explosion-proof, dust-proof) 3. High light transmittance, no ...

Weiluntong contact screen repair 　　The first step in troubleshooting a touchscreen system is to determine if the problem is related to the display, software, or hardware: Don't confuse the visibility issue with the contact screen issue, the two are unrelated. Software problems are caused by fundamental hardware functions ...

1. The direct window element can realize the bit-address control window pop-up. Setup Steps: 1. Click [Components] in the menu bar - click the "Direct Window" component under [Embed Window]. 2. The dialog box shown in the following figure pops up, specify the "Read Address". ...

Weiluntong touch screen, also known as "touch screen", "touch panel", is a kind of inductive liquid crystal display device that can receive input signals such as contacts, when touching the graphic buttons on the screen, the haptic feedback system on the screen can drive various connection devices according to the pre-programmed program, which can be ...

1. Omron NJ controller programming 1. The structure data type required for the new project, such as the Boolean switch to be used in this example to create a structure data type of "take-up machine IO", and the integer data used in this example to create a "take-up machine".

First of all, the yellow one on the left side of the infrared touch screen is the high-voltage input line. Continue to boost the 220V of the power supply to the top of kilovolts and input it to the LCD panel. The green one on the right is the screen driver board, which is used to drive the LCD panel. Here's how to connect, find the VGA cable ...

Four-wire: Because of factors such as cost and mature technical level, four-wire touch screen is almost the most basic production specification for touch screen practitioners. First of all, in terms of resistive touch screen technology, four-wire touch screen accounts for more than 50% of the market. It is composed mainly ...

Sometimes we need to monitor and change the program of PLC equipment, and when it is inconvenient to connect to PLC or there is no communication line, we can choose to achieve it through the penetration function of the touch screen. The traversal communication function consists of the following two modes: Ethernet When using [Ethernet] ...

Model 1, MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Model two, MT500, this model is following the previous model, after the launch of the very good ...

Why can't the infrared touch all-in-one machine be calibrated? 1. It is possible that the touch screen control card receives the operation signal before the host starts to load the touch screen driver, please power off and restart the computer and recalibrate. 2. It is possible that the sound wave screen is used for a period of time, ...

Store Payments The checkout counter of the store now uses a computer interactive terminal device. By operating the touch screen, the customer may print out a payment slip with the name and price of the goods. On the terminal, you can use the full-screen video image to promote the product, and the customer can ...

1. The line interface of the Weilun Tong touch screen is faulty. 2. Whether there is a crack fault on the surface of the touch screen. 3. External interference and control box failure. 4. The connection between the touch screen and the host or the host is faulty. ...