On March 11, Nanjing Estun Automation Co., Ltd. (hereinafter referred to as Estun) and Beijing Machinery Industry Automation Research Institute Co., Ltd. (hereinafter referred to as Beijing Institute of Automation) joined forces and reached a strategic cooperation agreement. Wang Zhenlin, Secretary of the Party Committee and Chairman of the Beijing Autonomous Institute, Estun Automatic ...

Recently, Nanjing Estun Automation Co., Ltd. (hereinafter referred to as Estun Automation) and Sany Robot Technology Co., Ltd. (hereinafter referred to as Sany Robot) held a strategic cooperation signing ceremony in Changsha, and the two sides will establish a long-term strategic partnership in the field of intelligent manufacturing. 　　Meeting...

1. Position proportional gain Set the proportional gain of the position ring adjuster; The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillation or overshoot; The parameter values are determined by the specific servo system type ...

1. Select magnet wires with good corona resistance to meet the requirements of high-frequency pulse resistance and partial discharge of the motor. Generally, polyesterimide/polyamideimide composite layer enameled wire is used, which is corona resistant and corona resistant magnet wire. Second, winding, embedded wire construction technology. Frequency conversion...

The daily inspection is mainly to monitor the start-up and operation of the motor, find abnormal phenomena in time, and prevent accidents. Generally, it is carried out by looking, hearing, touching, smelling, asking and monitoring the ammeter and voltmeter. (1) Observe whether the motor has abnormal noise and vibration. Especially...

Point 1: Whether the speed of the motor is normal, whether there is speed jitter and stall (can be checked with a tachometer). Point 2: Whether the anchor bolts of the motor are loose, whether the foundation is intact, and whether there are debris around. Point 3: Whether the housing and coupling of the motor are in good condition, ...

1. The electromagnetic torque of the synchronous motor is the interaction between the rotating magnetic field of the stator generated by the power supply voltage and the main magnetic field of the rotor; 2. The intersection angle of the magnetic pole axis of the rotating magnetic field of the stator and the main magnetic field of the rotor is called the work angle; 3. When the power angle is zero, the electromagnetic torque is zero, and the work is zero.

1. Fault phenomenon: The uneven distribution of the magnetic field of the ions, the unbalanced three-phase current aggravates the vibration and noise of the motor during operation, and the motor cannot be started when it is serious, and a large short-circuit current is generated in the short-circuit coil, which causes the coil to heat up rapidly and burn out. 2. Causes: ...

1. What is "inertia matching"? 1. According to Newton's second law: "The required moment T of the feed system = the transmission inertia of the system J×angular acceleration θ angle". The acceleration θ affects the dynamic characteristics of the system, the smaller θ, the more time from the controller to the completion of the system's execution.

1. Protection of servo motor oil and water A: The servo motor can be used in places where it will be attacked by water or oil droplets, but it is not completely waterproof or oil-proof. Therefore, servo motors should not be placed or used in water or oil-infested environments. B: If the servo motor is connected to a ...

Servo motor selection: Rotational speed (choose as required) Torque (the torque that needs to be output by the servo motor is calculated according to the load structure and weight, as well as the rotational speed) Moment of inertia (this parameter relates to the running accuracy of the servo on the mechanical structure, by the weight of the load structure ...

1. Torque control: The torque control mode is to set the size of the output torque of the motor shaft through the input of the external analog quantity or the assignment of the direct address, which is specifically manifested as if 10V corresponds to 5Nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5Nm: if the motor shaft ...

The following preparations need to be made for starting when the motor is put into operation after installation or before it is put back into operation after being shelved for a long time: (1) Use compressed air to blow off the dust attached to the inside of the motor, and remove the wrapping paper at the windshield for new motors. Check whether the bearing grease is clean and suitable.

(1) Check the circuit condition (including the connection of power supply, controller, wiring and measuring instrument, etc.), check whether the spring of the starter is flexible and whether the contact is good. (2) When the constant voltage power supply is supplied, it needs to be started with a starter. Closed power switch, under motor load, ...

Speed regulation of DC motors Constant power weak magnetic upward speed regulation, the magnetic field governor can be adjusted until the speed reaches the required value, but shall not exceed the maximum speed allowed by the technical conditions. Constant torque loads can be slowed down by step-down or armature string resistors. Downtime of the DC motor ...

Special attention should be paid to the following matters when the motor is regularly inspected during use: 1. The area around the motor should be kept dry, and no other objects should be placed inside and outside it The cleaning of the motor shall not be less than once a month, and the dust inside shall be blown off with compressed air during cleaning.

1. Applicable welding methods and cutting methods: Generally, arc welding robots are only suitable for MIG/MAG welding, and there is no interference of high-frequency arc striking on the control and drive system of the robot. Whether it can be used for tungsten argon arc welding depends on whether the robot has a special anti-interference method.

CALIB Command: This instruction calibrates joint position sensors. STATUS command: Used to display the status of the user's program. FREE command: This command displays the unused storage capacity. ENABL command: used to turn the system hardware on and off. ZERO Directive: This directive ...

A51: The robot spindle servo motor is abnormal. It could be a cable failure, a servo drive problem, a damaged spindle bearing, etc. A47: The servo motor is overheating. It may be because the external ambient temperature is too high, the servo motor is starting to break, and it cannot be cooled properly. A4 ...

1. Estun servo motor maintenance 1; Overload alarm A04 1. The wiring of the servo motor is wrong or the wiring is leaking (1) The U, V, and W phase wires of the motor are connected incorrectly (2) Whether the insertion of the connector on the servo motor side is defective 2. The model of the servo drive and the motor does not match ...

Alarm code A04 refers to: Alarm mechanism: The overload rate of the drive accumulates to a certain threshold and triggers an alarm. Causes: 1. Servo motor brake control circuit problem; 2. Robot power cable problem; 3. The drive parameter setting is wrong; ...