1. Initialize parameters Before wiring, initialize the parameters. On the control card: select the control mode; Reset the PID parameter to zero; When the control card is powered on, the enabling signal is turned off by default; Save this state to make sure that this is the status when the adapter is powered on again. Serving ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure: (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring of the control equipment is incorrect. 2. Failure ...

1. Will the servo motor lose steps or walk inaccurately? The servo motor is controlled in a closed loop by the driver through the feedback of the encoder. After receiving each pulse command, the driver drives the motor to rotate at an angle, and checks whether the motor is rotated to a given point by the encoder

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

On June 17, 2021, at the same time of the 25th Essen Welding Exhibition, Estun Automation and its wholly-owned subsidiary CLOOS released a number of new welding robots and new welding power supplies in Shanghai. ESTUN Weld Automation Set EWAS series welding robots EWAS ...

What points do you need to pay attention to when using welding robots? 1. It is necessary to teach the robot before active welding, and it is necessary for the operator to teach the track of the robot welding gun and set the welding conditions. Because it is necessary to teach, the robot is not oriented to many classes ...

AC servo motors are usually single-phase asynchronous motors, with two structural forms: squirrel cage rotor and cup rotor. Like ordinary motors, AC servo motors are constructed of a stator and a rotor. There are two windings on the stator, namely the excitation winding and the control winding, and the two windings are 90 ...

1. The control system has the function of input and output. Most of the welding robots are programmed offline, and the technicians write the welding program in advance, and then input the welding program into the control system, and the control system intelligently identifies the weld standard through the sensor, selects the appropriate welding parameters, and ...

1. The capacity of the industrial-grade intelligent power module IPM selected by the EMJ/EMG/EML/EMB servo drive is one level larger than that of similar servo products that are usually calibrated with the same power, so it has the characteristics of strong overload capacity, strong anti-load disturbance ability, large starting torque, etc., and can ensure that the product is less than 1.5KW.

AC servo motor (1) Cage type two-phase AC servo motor (slender cage rotor, mechanical characteristics are approximately linear, small volume and excitation current, small power servo, low-speed operation is not smooth enough) (2) Non-magnetic cup rotor two-phase AC servo motor (coreless rotor, mechanical ...

1. The palletizing robot is mostly four-axis, flexible in operation, and the load can reach 180 kg. 2. It can carry out high-precision handling and palletizing work, save a lot of labor for enterprises, and promote modern production. 3. Customized according to the on-site needs of the enterprise, high work efficiency, 24 hours uninterrupted...

One: personal protection The safety operation procedures of welding robots are first of all to do a good job of personal protection, and the maximum scale of welding robot operations is set up outside the protective fence or cordon, and personnel are not allowed to enter the scale of their operations in the welding robot operation. In the process of welding robot operation, it is necessary to ...

1. Motor encoder alarm 1. The cause of the failure (1) Wrong wiring; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment; 2. Troubleshooting (1) Check the wiring and troubleshoot the error ...

1. The clamping action of the palletizer is too slow or the clamping stroke of the nail is insufficient. Causes and solutions: bolts are loose, and the front buckle or inner piece of the board machine is worn. The bolt can be tightened, paying attention to the correct position of the front buckle shaft. You can replace the front buckle or the inner piece of the board machine, after completing the above actions, test its function, if the line ...

The speed control and torque control of the servo motor are controlled by analog quantity, and the position control is controlled by generating pulses. The specific control method to use should be selected according to the customer's requirements and what kind of motion function is satisfied. Generally, there are three control modes for servo: speed control ...

Troubleshooting and Detection Causes of Estun Controller: 1。 The servo amplifier is based on the effective value of the output torque 2. Calculate the load factor. If the value exceeds PR5 12, protection is generated. 3. From the amplifier front panel above the "D15. ol' monitoring mode or panatermm...

1. Problems in the application of industrial robot palletizing Palletizing gripper problems The ability of the palletizing robot to work under different operational tasks mainly depends on the design of the robot flange crane. The quality and performance of the robot crane directly affects the work of the industrial handling robot ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct obstruction 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

1. Motor encoder alarm 1. The cause of the failure (1) Wiring fault; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment. 2. Fault cleaning (1) Check the wiring and sweep away the fault ...

The 2021 China International Medical Equipment Fair will be held from May 13 to 16 at the National Convention and Exhibition Center in Shanghai. Estun Medical will exhibit the unilateral and bilateral versions of the Burt Upper Limb Rehabilitation Training System, which is more suitable for the full-cycle rehabilitation training program of the rehabilitation population, and includes adaptation ...

Common system failures during the welding process 1. Collision of guns: It may be due to the error of workpiece assembly or the inaccuracy of the TCP of the welding gun, you can check the assembly situation or correct the TCP of the welding gun. 2. Arc fault, unable to start the arc: it may be due to the fact that the welding wire does not contact the workpiece or ...