The servo?mechanism is a process control system that enables the output of the direction, direction, and condition of the block to change at will according to the input overall goal (or given value). How to finish the Mitsubishi servo motor ...

1. Main substrate There are a variety of models such as Q32SB, Q33SB, Q35SB, Q33B, Q35B, Q38B, Q312B and other main substrates for Q series PLC, and the meaning of the model is as follows: In the meantime, the "S" stands for ultra-thin main substrate, and only Q61SP power modules can be used, and they cannot be ...

1. Mitsubishi inverter is more and more widely used because of a series of advantages such as wide speed regulation range, high speed regulation accuracy, fast dynamic response, high work efficiency, convenient operation and easy interface with other equipment. Because of the high common sense content of Mitsubishi inverter and the messy technology, how to use Mitsubishi inverter well...

The inverter can be preset with a number of different speed points, and then complete the scheduling of multiple speed stages. The specific completion method is as follows: You can set a number of different speed points in the VFD, and you can generally set the maximum speed, minimum speed, and several center speed points. According to the needs, choose ...

1. The actual output waveform of the inverter is PWM wave, which contains carrier signals in addition to the fundamental wave. The carrier signal frequency is much higher than that of the fundamental wave, and it is a square wave signal, which contains a lot of higher harmonics, and the test system requires a higher sampling frequency and bandwidth. ...

The reasons for the loss of the PLC program are the lack of battery power supply for the user's saved program, the internal circuit of the PC, the motherboard burned out due to the impact of external high voltage such as lightning strikes, etc., which will be encountered in our PLC control system. For example, the old type of plc such as the FX2N series, which has been discontinued...

1、3相200V FR-E820-[]K (E) 　　FR-E820-0.1K、FR-E820-0.2K、FR-E820-0.4K、FR-E820-0.75K、FR-E820-1.5K、 　　FR-E820-2.2K、FR-E820-3.7K、FR-E820-5.5K、FR-E820-7.5K、FR-E820-11K、 ...

1. Step Instruction (STL/RET) Step instruction is an instruction that is specially planned for sequential control. In the field of industrial control, many control processes can be completed by sequential control, and the use of step instructions to complete sequential control is not only convenient to complete, but also easy to read and modify. There are two in the FX2N ...

The origin orientation is incorrect, and the encoder debugs/zeros the bit Replacement of bearings, wear of bearing grooves, cracking of the rotor, cracking of the shaft Gear groove wear The magnet bursts steel, the magnet falls, gets stuck and doesn't move Encoder wear, code/glass disc wear and crack ...

Because the output voltage of the inverter (Variable-frequency Drive, VFD) is generally 380 volts, there should be no problem in direct measurement, but in practice, most multimeters cannot get a correct reading when testing the output voltage of VFD, and in some cases the multimeter may be burned directly. ...

Mitsubishi CPU module engineering creation method Start engineering tools, create projects. [Establishment process] 1. Select the CPU module to be used in the "Model" item. In the "Programming Language" project, select ...

1. Mitsubishi PLC's analog signal control inverter Hardware: FX1N, FX2N PLC hosts, equipped with 1 simple FX1N-1DA-BD extended analog output board; or analog input-output hybrid module FX0N-3A; or FX2N-2DA with two outputs; or four outputs ...

The capacity (non-functional) of the Mitsubishi inverter for the drive motor can be understood from the change in energy flow determined by the operation method. 1. When accelerating or operating at constant speed The efficiency of the inverter is the output current, that is, how much current the inverter can provide to the motor. Frequency converters ...

First, the control accuracy is different The step angle of the two-phase hybrid Mitsubishi servo motor is generally 1.8 ° and 0.9 °, and the step angle of the five-phase hybrid Mitsubishi servo motor is generally 0.72 ° and 0.36 °. Mitsubishi servo motors, which are also some functions, have a smaller step angle after segmentation. ...

First, Mitsubishi uses FX5U series PLC with serial port and built-in modbus communication protocol, so that we can easily communicate with third-party equipment. If it is a communication between Mitsubishi PLC and the inverter, the focus is on designing the parameters. The inverter is heavy, set the address, baud rate, check, etc., ...

Capacitor is a kind of energy storage element, with the characteristics of "straight through AC, low frequency through high frequency", people in order to know and identify the capacitor in different circuits, according to its effect in the line and give it many titles, the following introduces the meaning of some commonly used titles. ...

The three output types of PLC are: transistor output, thyristor output and relay output, what is the difference between these three different output types? (1) Transistor output: The biggest advantage is that it is adapted to high-frequency action, and the echo moment is short, generally about 0.2ms, but it ...

1. Routine control is consistent with safety control In the MELSEC-QS series, it is necessary to prepare a system for conventional control and a system for safety control. With the MELSEC iQ-R series of safe programmable controllers, it is possible to combine conventional and safe control into a single system. Quiet...

1. For the test of the power output capacity of the driving circuit, to detect the pulse terminal signal such as GU\EU, it is not possible to have voltage (or pulse waveform) alone, and the current output capacity should be detected, and then admit whether it is normal; 2. Admit the defects of the current transformer. My solution is to use the ...

1. Use the switching signal of PLC to control the inverter The output point and COM point of the PLC (MR type or MT type) are directly connected to the STF (forward engine), RH (high speed), RM (medium speed), RL (low speed), and SG input ports of the inverter. The PLC can control the inverter through the program.

FX1S Series: Mitsubishi PLC is an integrated small unit type PLC. And it has intact functions and communication functions and other scalability. If you consider the space and cost of the installation, it is an ideal choice. FX1N Series: It is a popular PL with strong functions launched by Mitsubishi Electric ...