How to disassemble the five or six axes of Estun robot?

1. Open the robot control software: use the computer to connect the robot, start the control software, and enter the robot control interface. 2. Select the point mode: select the point mode in the control interface, in the point mode, the robot will record and execute the point set by the user. ...

Servo drive is a kind of controller used to control servo motor, its role is similar to the inverter to ordinary AC motor, as a precision equipment, it will inevitably have some faults in the process of use, common faults and maintenance methods are as follows: 1. When the motor rotates, the LED light ...

Estun Server Alarm A.01 Parameter Broken Estun server alarm A.02 A/D is damaged Estun Server Alarm A.03 Overspeeding Estun server alarm A.04 Overload Estun Server Alarm A.05 Position Deviation Counter Overflow Ace...

A51: The robot spindle servo motor is abnormal. It could be a cable failure, a servo drive problem, a damaged spindle bearing, etc. A47: The servo motor is overheating. It may be because the external ambient temperature is too high, the servo motor is starting to break, and it cannot be cooled properly. A4 ...

First, the control accuracy is different The step angle of the two-phase hybrid stepper motor is generally 3.6 ° and 1.8 °, and the step angle of the five-phase hybrid stepper motor is generally 0.72 ° and 0.36 °. There are also some high-performance stepper motors with smaller step angles. Such as Sitong company produced a kind of wire for slow wire ...

11. What is the principle of parameter adjustment of speed loop and position loop of servo drive? In addition to the performance of the motor and the drive, the adjustment of the drive parameters is also a very critical factor. The main performance parameters of the servo drive ...

AC servo motors are usually single-phase asynchronous motors, with two structural forms: squirrel cage rotor and cup rotor. Like ordinary motors, AC servo motors are constructed of a stator and a rotor. There are two windings on the stator, namely the excitation winding and the control winding, and the two windings are 90 ...

Cause of failure and solution: (1) The phase sequence of the motor is out of order and the encoder is abnormal, check whether the power line of the motor (U, V, W, D) is connected incorrectly, and whether the encoder connection is not in good contact. (2) The motor model parameters do not match, check and reset the server Pn parameters or more...

Troubleshooting and Detection Causes of Estun Controller: 1。 The servo amplifier is based on the effective value of the output torque 2. Calculate the load factor. If the value exceeds PR5 12, protection is generated. 3. From the amplifier front panel above the "D15. ol' monitoring mode or panatermm...

1. Applicable welding methods and cutting methods: Generally, arc welding robots are only suitable for MIG/MAG welding, and there is no interference of high-frequency arc striking on the control and drive system of the robot. Whether it can be used for tungsten argon arc welding depends on whether the robot has a special anti-interference method.

Common system failures during the welding process 1. Collision of guns: It may be due to the error of workpiece assembly or the inaccuracy of the TCP of the welding gun, you can check the assembly situation or correct the TCP of the welding gun. 2. Arc fault, unable to start the arc: it may be due to the fact that the welding wire does not contact the workpiece or ...

1. Positional proportional gain Sets the proportional gain of the position ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillations or overshoots. The parameter values are determined by the specific servo model ...

(1) The motor heat dissipation system is faulty The temperature of the motor rises due to the heat generated by the motor not being dissipated quickly. At this time, the main solution is to check whether the cooling fan of the motor is operating normally and whether the direction of rotation of the fan is correct. The surface of the motor is ...

Estun Robotics FAQs. 　　After turning over the main switch of the control cabinet, there is no power, the cause analysis and treatment methods: Please check whether the power supply line of the electric control cabinet is correct; Please check whether the external power supply voltage meets the type of three-phase AC380V power supply robot Please acknowledge that the cabinet is broken...

Servo motor refers to the engine that controls the operation of mechanical components in the servo system, and is a kind of auxiliary motor indirect transmission device. The servo motor can make the control speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. Servo motor rotor speed ...

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

1: A motor deviation counter overflow error occurs when a long instruction pulse is entered. Causes and solutions (1) Generally, the gain setting is too large, and we can manually adjust the gain or adjust the gain automatically. (2) The load is too heavy, and it needs to be ...

Generally, there are three control modes for servo: speed control mode, torque control mode, and position control mode. 1. Speed control (1) Speed system, that is, the motor runs according to the given speed command. (2) The application of speed control is quite wide-ranging ...

Estun Server Alarm A.01 Parameter Broken Estun server alarm A.02 A/D is damaged Estun Server Alarm A.03 Overspeeding Estun server alarm A.04 Overload Estun Server Alarm A.05 Position Deviation Counter Overflow Ace...

(1) Small inertial DC servo motor The small inertia straight sinking servo motor is named because of the small rotation of the inertia basin. This type of motor is generally hydromagnetic, and there are three types of armature windings: phaseless armature type, printed armature type and coreless armature type. Because the small inertia DC motor minimizes the armature's ...