Estun servo drive alarm A20 common fault analysis

The daily inspection is mainly to monitor the start-up and operation of the motor, find abnormal phenomena in time, and prevent accidents. Generally, it is carried out by looking, hearing, touching, smelling, asking and monitoring the ammeter and voltmeter. (1) Observe whether the motor has abnormal noise and vibration. Especially...

Servo drive is a kind of controller used to control servo motor, its role is similar to the inverter to ordinary AC motor, as a precision equipment, it will inevitably have some faults in the process of use, common faults and maintenance methods are as follows: 1. When the motor rotates, the LED light ...

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

On April 6, Nanjing Estun (002747) Automation Co., Ltd. officially signed a contract with the Chengdu Chenghua District Government, and the Estun Industrial Robot Intelligent Manufacturing Base Project was officially settled in the Longtan Industrial Robot Industry Functional Zone in Chenghua District. It is reported that in the Longtan industrial robot industry...

1. The palletizing robot is mostly four-axis, flexible in operation, and the load can reach 180 kg. 2. It can carry out high-precision handling and palletizing work, save a lot of labor for enterprises, and promote modern production. 3. Customized according to the on-site needs of the enterprise, high work efficiency, 24 hours uninterrupted...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

1. The control system has the function of input and output. Most of the welding robots are programmed offline, and the technicians write the welding program in advance, and then input the welding program into the control system, and the control system intelligently identifies the weld standard through the sensor, selects the appropriate welding parameters, and ...

On September 15, 2020, the grand opening of the China Industry Expo, Estun Automation joined hands with TRIO, CLOOS, M.A.i to focus on complete solutions for industrial automation, industrial robots, and intelligent manufacturing.

1. Motor encoder alarm 1. The cause of the failure (1) Wrong wiring; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment; 2. Troubleshooting (1) Check the wiring and troubleshoot the error ...

1: A motor deviation counter overflow error occurs when a long instruction pulse is entered. Causes and solutions (1) Generally, the gain setting is too large, and we can manually adjust the gain or adjust the gain automatically. (2) The load is too heavy, and it needs to be ...

Recently, Nanjing Estun Automation Co., Ltd. (hereinafter referred to as Estun Automation) and Sany Robot Technology Co., Ltd. (hereinafter referred to as Sany Robot) held a strategic cooperation signing ceremony in Changsha, and the two sides will establish a long-term strategic partnership in the field of intelligent manufacturing. 　　Meeting...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure: (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring of the control equipment is incorrect. 2. Failure ...

1. Fault phenomenon of servo motor encoder Due to improper loading and unloading, the encoder code disc is cracked and worn 2. Reasons for damage to servo motor encoders 1. Due to the abnormal external force on the motor shaft, the encoder code disc is displaced with the shaft, and the light receiving mirror is rubbed and grinded.

From the perspective of the protection response speed of the robot servo drive, Estun has a small amount of calculation in the form of torque, and the response to the control signal of the drive is fast. The azimuth form has a large amount of computation, and the response to the driver's control signal is slow. 1. If there is a relatively high demand for dynamic functions in sports...

1. Motor encoder alarm 1. The cause of the failure (1) Wiring fault; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment. 2. Fault cleaning (1) Check the wiring and sweep away the fault ...

Precautions for servo motors: 1. Protection of servo motor oil and water A: The servo motor can be used in places where it will be attacked by water or oil droplets, but it is not fully waterproof or oil-proof. Therefore, servo motors should not be placed or used in water or oil-infested environments. ...

AC servo motor (1) Cage type two-phase AC servo motor (slender cage rotor, mechanical characteristics are approximately linear, small volume and excitation current, small power servo, low-speed operation is not smooth enough) (2) Non-magnetic cup rotor two-phase AC servo motor (coreless rotor, mechanical ...

1. Take out the Eston four-axis robot and place it in front of your body. 2. After placing it in front of the body, take out the instruction manual of the Estun four-axis robot and read the instruction manual carefully. 3. Set the point according to the requirements of the manual. ...

6. What should I pay attention to when using the motor? Check the following before powering on: 1) Whether the power supply voltage is appropriate (overvoltage is likely to cause damage to the drive module); The +/- polarity of the DC input must not be misconnected, and the motor model or current setting on the drive controller ...

1. Initialize parameters Before wiring, initialize the parameters. On the control card: select the control mode; Reset the PID parameter to zero; When the control card is powered on, the enabling signal is turned off by default; Save this state to make sure that this is the status when the adapter is powered on again. Serving ...