PILZ WILL BE EXHIBITING AT THERMPROCESS 2023

1. The structure/working principle of the two is different Mechanical relays consist of an iron core, coils, and contacts. When the coil is energized, the current in the coil generates a magnetic field that makes the contacts act, thus completing the working principle of the mechanical relay. Solid state relays are made up entirely of electronic components. That...

The Pilz safety proximity switch also belongs to a position sensor with a switching output, its measuring head is usually a plate that constitutes a capacitor, and the other plate is the object itself, when the object moves towards the proximity switch, the dielectric constant of the object and the proximity switch changes, so that ...

1. The role of intermediate relays It plays the role of converting and transmitting control signals, that is to say, its input signal is the energizing and power-off signal of the coil, and the output signal is the contact action of the intermediate relay. Essentially, it is a type of voltage relay ...

The safety switch prevents personnel from entering the hazardous area until all safety conditions have been met Provide bolt switches, safety magnetic switches, safety door lock switches, safety rope pull switches, emergency stop buttons, twisted chain interlocking switches, safety enable switches, safety limit switches, explosion-proof open...

Why can't ordinary relays be used in safety-related applications? Ordinary relays use the mechanical action of coils and metal contacts to switch loads. Metal contacts may be fusion welded due to repeated operations. Once this happens, the machine will also be ...

The use of safety locks If there are hazards in the equipment, such as moving levers, rotating mechanisms or even robots, in order to avoid damage to the operator, a safety gate system will be added to the protective cover (door). Safety door interlocking devices are widely used in the field of industrial safety. ...

PNOZ m EF EtherCAT FSoE is a forthcoming safety bus communication module from Pilz that supports the FSoE (FailSafe over EtherCAT) protocol. As a new member of the PNOZ multi 2 family, the module can be used as an FSoE master with a maximum cycle time of 10 ms ...

1) The installation of the switch panel should be after the installation of the lamp, and the switch must be connected in series on the live line; Application of sealed or protected sockets in wet locations; The allowable deviation of the verticality of the panel is not more than 1mm; The gap between the panels installed in rows should not be greater than 1mm. 2) Where the socket must be facing the switch panel ...

Applications for Solid State Relays (1) The recommended value of the foreign SSR trigger signal (i.e., the current through the light-emitting tube) is 10mA DC, and the recommended value of the domestic SSR trigger signal is 12-25mA DC. (2) Multiple SSRs can use the same trigger signal, which is common in the control of three-phase AC loads.

Pilz's safety validation services for plants and machines can now be customised to suit your needs, choosing between three different validation levels. This guarantees an efficient service tailored to individual requirements, allowing plants and machines to be designed in accordance with standards and with maximum safety. In the wind ...

Pilz safety relays consist of several relays and circuits to compensate for each other's abnormal defects and achieve the full functionality of a relay with low misoperation or even correct relays. The lower the fault value and fault, the higher the safety factor. In order to prevent unavoidable misoperation or natural wear and tear of the machine, it should also be ...

Pilz safety light curtains provide cost-effective safety for applications that require body protection. The safety light curtains have a wide operating range of up to 55 m and are ideally suited for the demarcation of external areas. Whether the user wants a single beam or a multi-beam encoder, in the PSENopt and PSENopt II series, there is a choice of 2 ...

From hardware components to complete safety concepts: Pilz has extended its industrial expertise from the field of machinery safety and health and safety regulations to railway sites. With many years of knowledge and experience, Pilz has demonstrated the same competence in the railway industry as it does in an industrial environment. Skin...

1. The mount can be quickly replaced. 2. For low-value and easy-to-purchase multi-leg assemblies, destructive removal methods can be employed to prevent board stepping on. For this type of relay, use pliers to break it off and then use a set with a semicircular or triangular file.

Single-phase servo amplifier (referred to as amplifier), with a variety of quarter-turn, linear stroke, multi-turn single-phase electric actuator (electric actuator) matching, widely used in industrial automation control process in the automatic adjustment system, this amplifier is an improvement of the traditional amplifier, compared with the traditional ...

IO-Link is an open sensor communication protocol that represents a powerful and standardized (IEC 61131-9) connection technology in the field of point-to-point communication and is fieldbus and system independent. The communication protocol will also be used for functionally safe data exchange in the near future. The advantages of IO-Link are ...

The technology and business of rail freight have remained the same for decades. Until now, in order to test the brakes of freight trains, the crew would walk around the entire train and hit each axle with a special hammer to check the proper operation of the braking system. Rail transport systems in Austria ...

　　1. The same module can be triggered by high or low level through different wiring, and the trigger current is not less than 1mA, and the output capacity of the IO port of some 51 single-chip microcomputers is weak, and the circuit of pulling up or increasing the driving capacity is required (the default is low level triggering); 2. Advantages of low-level drive, ...

Since its launch, Pilz's flagship product, the configurable and safe small controller PNOZmulti, has been impressed by users for its robustness, flexibility and ease of operation. PNOZmulti Configurator as a configuration tool for the safe small controller PNOZmulti ...

1. Determine the voltage range that needs to be regulated: First of all, you must clarify the voltage range you need to regulate, as well as the specifications of the high and low voltage relays and the voltage range that can be adjusted. If there is no clear scope and specifications, you can check the relevant manuals of high and low voltage relays or consult the equipment manufacturer.