Pilz: Designing safe railway sites

On fully enclosed rail transit lines, viaducts or tunnels are usually used to avoid the impact of rail lines on the distance, while on non-fully enclosed rail transit lines, the plane intersection between the railway and the distance, that is, level crossings, is more common. In the early stage, rail transit ...

With the rapid rise of new energy vehicles, the lithium battery industry has also ushered in explosive growth. The production process of lithium battery is more complex, and the production process of different battery types is also different, but the manufacturing process is roughly the same, which is the front process (pole piece production), the middle ...

Key in Pocket has attracted attention since its introduction as an alternative to tagout lockout, as it not only improves work safety and optimizes workflows, but also provides convenience and productivity for workers in the field. Key in pocket is actually IAM ( ...

1. When the emergency stop is lifted, the machine cannot be suddenly restarted 2. In case of failure of the machine safety circuit, the power supply of the machine can be stopped 3. When the safety circuit fails, the machine can no longer be started Confirm safe input such as safety switches, light curtains, etc.

ACMI S.p.A. is an Italy company specializing in high-tech bottling and packaging lines. Based in Fornovo Taro, in the province of Parma, Italy, the company initially produced palletizers and depalletizers for the food and beverage industry, and later specialized in all packaging processes. For...

Today we share with you the case of ACMI S.p.A., an Italy company dedicated to the production of high-end filling and packaging lines, to see how they do the safety protection of canning lines. 　　Let's start with their process...... This mineral water filling ...

1. The mount can be quickly replaced. 2. For low-value and easy-to-purchase multi-leg assemblies, destructive removal methods can be employed to prevent board stepping on. For this type of relay, use pliers to break it off and then use a set with a semicircular or triangular file.

The use of safety locks If there are hazards in the equipment, such as moving levers, rotating mechanisms or even robots, in order to avoid damage to the operator, a safety gate system will be added to the protective cover (door). Safety door interlocking devices are widely used in the field of industrial safety. ...

1. When the emergency stop is lifted, the machine cannot be suddenly restarted 2. In case of failure of the safety circuit of the machine, the power supply of the machine can be stopped 3. When the safety circuit fails, the machine can no longer be started Confirm the safety of the transmission such as safety switches, light curtains, etc.

1. After opening, establish a reliable insulation gap to separate the equipment or line that needs to be overhauled from the power supply with an obvious disconnection point to ensure the safety of maintenance personnel and equipment. 2. According to the operation needs, change the line. 3. It can be used to divide and combine small currents in the line, ...

　　1. The same module can be triggered by high or low level through different wiring, and the trigger current is not less than 1mA, and the output capacity of the IO port of some 51 single-chip microcomputers is weak, and the circuit of pulling up or increasing the driving capacity is required (the default is low level triggering); 2. Advantages of low-level drive, ...

PNOZ m EF EtherCAT FSoE is a forthcoming safety bus communication module from Pilz that supports the FSoE (FailSafe over EtherCAT) protocol. As a new member of the PNOZ multi 2 family, the module can be used as an FSoE master with a maximum cycle time of 10 ms ...

1. The switch binding post is generally marked with L, L1, L2. When the L end enters the line, L1 and L2 have one end and L on, and after pressing the switch, the other end of L1 and L2 is connected to L. 2. Peel the thread with diagonal pliers first, and be careful not to leave too long the thread to avoid touching. 3. To the left ...

The Pilz safety proximity switch also belongs to a position sensor with a switching output, its measuring head is usually a plate that constitutes a capacitor, and the other plate is the object itself, when the object moves towards the proximity switch, the dielectric constant of the object and the proximity switch changes, so that ...

1. Classification by use In terms of use, the classification of relays can be divided into two types: control relays and protection relays. In the meantime: thermal relays, overcurrent relays, and undervoltage relays are all protective relays. And moment relays, speed relays, intermediate relays ...

How do you grasp the issues of employee protection, responsibility protection, work efficiency, and data protection? How can you improve quality and at the same time prevent machines from being tampered with? How can data and employees be protected in equal measure? Through I.A.M. (Identification and Access Management) "...

Selection and features of Pilz safety relays: 1. Understand the necessary conditions first The power supply voltage of the control circuit, the maximum current that can be delivered; voltage and current in the controlled circuit; How many sets of contacts and what form of contacts are required for the controlled circuit. Choosing the following ...

1. High-precision detection: high and low voltage relays can detect high and low voltage signals with high precision, and realize accurate monitoring and control of electrical equipment. 2. Large capacitance switch: High and low voltage relays have good durability and stability when switching high capacitance loads. ...

Franz Haas, the founder of the Bühler Group, invented the first wafer machine as early as the end of the 40s of the 20th century. Today, its subsidiaries are spread all over the world. In the wafer area of the consumer food division in Leobendorf, 700 employees are engaged in development, design and production, as well as sales, service, maintenance ...

In addition to the usual emergency stop monitoring, safety gate monitoring, light barrier monitoring and two-hand button monitoring, the safety relays of the PNOZsigma family are also functional, as well as safe speed monitoring, safe braking and braking monitoring. Voltage monitoring safety relays are also one of its features. PNO ...