How to use the Kunlun Tongtai operating environment upgrade package

The five-wire resistive touch panel is composed of two layers: (1) ITO Glass: A piece of glass or plexiglass is used as the substrate, and the surface is coated with a transparent conductive layer. (2) ITO polyester plastic layer (ITO Film): The surface is hardened to make the surface smooth and ...

Problems with the Internet version 1. How to calculate the number of points of MCGS configuration software In the real-time database, except for the 4 internal variables of the system, all the added variables are counted as points of the software, and you can click "Tools - Use Count Check" to view the MCGS points information. 2. Net ...

1. Do not stack resistive screens, use tray disks. 2. Do not use corrosive organic solvents to wipe the surface of the touch screen film. Such as industrial alcohol, etc. 3. When cleaning the surface of the product, it is necessary to wipe it with a soft cloth (deerskin) dipped in petroleum ether. ...

1. Do not hit with metal objects. Usually the HMI will be covered with a layer of glass to protect the screen and make it easy to touch. However, the glass is fragile, do not hit the screen with metal objects during use, it is easy to cause the glass to be scratched or broken. 2. Avoid squeezing the screen with heavy objects. Around HMI ...

91. How to update the TPC splash screen After the project is downloaded and the communication test is successful, click "Advanced Operation", in the advanced operation dialog box, select the corresponding file to replace the startup screen, and then click the "Change Startup Screen" button. Note: The splash screen is set ...

The first method: 1. Power off the touch screen and restart, enter the StartCenter interface, click Settings->OP->Device->Reboot->Prepare for Reset, and the screen will enter boot mode. Note: Before the factory reset, you must change the screen ...

Inaccurate screen position: Repositioning can be done via driver software. Touch position and screen cursor upside down: When installing the touch screen, the position of the screen is reversed, please adjust the touch screen position according to the principle of right-hand position out. The touchscreen display icon keeps pointing towards the fixed ...

1. How to check the communication status of the device in MVGS Among all non-board devices (except for some customized devices) of MCGS, *** channels are communication channels. That is, after entering the runtime environment, after the device driver starts working, the ...

MCGS Embedded is the main function of the configuration software 1. Simple and flexible visual operation interface: Adopt full Chinese and visual development interface, which meets the usage habits and requirements of Chinese. 2. Strong real-time performance and outstanding ...

1. In the Device window, click Select the device created by the variable. 2. Select the device configuration view option in the device editing window to check whether the configuration is correct. 3. When it appears, click OK when the device is viewed correctly. 4. Then select the OK button to save the data. ...

In May, ten seminars in East China and North China had just ended, and in June, Kunlun Tongtai attacked again, continuing the enthusiasm of Red May to June. The sky is blue and the clouds are white, and the Kunlun Tongguo Seminar (Beijing) Shunyi special session opened. On June 12, 2015, Kunlun Tongtai 2015 Seminar - Beijing

1. The film surface of the touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product 2. The touch screen part is a glass product, the corners of the glass are sharp, please wear gloves/finger sleeves when assembling 3. The touch screen part is a fragile glass product, and it should not be touched during assembly.

1. Click the "Settings" button on the MCGS interface to enter the settings interface. 2. Click on the "Alarm Answer" tab. 3. In the Alarm Response tab, check the Enable Alarm Response box, and set the Answer Time, Trigger Alarm Time Range, Response Time, Response Time, Alarm Response, Alarm Response, Alarm Response, Alarm Response, Alarm Response, Alarm Response,

96. How to check the status of the PC connection to the TPC network? Connect the PC to TPC with a network swap cable, click "Start-Run" on the PC, enter CMD enter in the run bar, and then enter the ping IP address in the DOS interface.

70. Omron PLC: Parent device parameter settings (1) The communication parameter setting of the parent device of the universal serial port should correspond to the communication parameter setting of the PLC serial port, and the default standard parameters of the PLC are set to: 9600, 7, 2, E (even check); (2) Users can set it according to their needs, and it is recommended to ...

1. Variables in the real-time runtime cannot add channels and send data using functions at the same time. 2. In the universal serial port parent device, the COM port indicates whether to select 232 or 485, and in the touch COM1 indicates the 232 interface, and COM2 represents the 485 interface. 3. View the touch ...

Open Kunlun Tongtai touch screen software, create a new [Window 0], and click to open. Find the Bitmap icon in the toolbox and click to open it. After creating a bitmap in Window 0, right-click and select Load Bitmap. Open the text where the image is saved ...

The first method: use a U disk to make the designed interface into a U disk function package, and then plug it into the touch screen, the touch screen will automatically detect and update it according to the prompts. The second method: use a special download cable for the touch screen, download the program, and it will automatically overwrite the original environment. ...

Kunlun Tongtai touch screen is a touch screen controller, which is generally used in embedded systems, such as industrial computers, embedded computers, intelligent terminals, etc. If you want to connect it to your computer to run, you can try the following methods: 1. USB interface: Kunlun Tongtai touch screen ...

Screen structure: ITO Film and ITO Glass are laminated, and the middle is isolated by a DOT point Outlet cable: FRC copper cable (flat conduction wire) length: 200mm Connection location with touch screen: Withstand tensile force: 2.0 kg horizontal with the screen, 1.0 kg vertical with the screen...