Fisher/Fisher dirty service trims

The Fisher V270 is a three-piece, full-bore control valve fitted with a bottom shaft designed from the bottom up to optimize pressure, flow, and process control. The V270 full-bore ball valve provides automated control in bypass, batch application, monitor, and emergency shut-off valve applications with virtually no ...

The Fisher 4660 pneumatic pilot-operated pressure controller activates a safe shutdown system for flowlines, production vessels, and compressors. The pilot is available in single or dual setpoint capability models that use a switching point to maintain full output pressure when the process pressure is within the set point range. If the process ...

Description: Fisher/Fisher's CSB400 series of direct-acting reed regulators can meet a wide range of pressure reduction applications in commercial and light industrial facilities. The flexibility is due to the fact that the regulator offers a wide range of body sizes and end connections, outlet pressures, and ...

Fisher 167D-2594-179127 Switching Valve 167DA Retaining Valve The 167D Series Switching Valve is typically used to provide reduced, stable vaporized liquid pressure to pilot-acting controllers and other pneumatic instruments. Models 167D and 167DS valves are two-way switching valves. 167DA and 167DA ...

The Fisher 3024C actuator is a compact, spring-balanced, pneumatic diaphragm actuator. It is a cast-type fork mounted for universal actuation of ball valves. This actuator can be used according to the pneumatic conveying of different controllers or valve positioners in the actuator diaphragm.

The Fisher TBX-T desuperheater can be used in a variety of applications to effectively reduce the temperature of superheated steam to the ideal set point. The TBX-T can be installed in steam lines with diameters DN 200 to DN 1200 (NPS 8 to 48) and can maintain steam temperatures at 6°C (10° ...

The Fisher D3 Control Valve is a compact, rugged valve for on/off or throttle control with FloPro technology and the choice of pneumatic or electric control. This valve is best used as a tipping valve for gas separators and scrubbers. At the same time ...

Y602 Series ventilation assemblies help prevent vent obstruction and ensure proper air or gas flow in regulator spring housings, remote ventilation ducts, actuator membrane housings, and other applications. These ventilation components are available in angled or straight-through versions. In general, angular ventilation components protect the side ...

The Fisher 377 guard valve assists in maintaining routine process operations that require a specific valve or actuator. When the compressed air pressure drops below the trigger point, the guard valve prevents the actuator from rising, locking in the previous position, or not descending. When the compressed air pressure rises above the trigger point, 3 ...

Description: The Fisher CSB700 Pressure Reducing Regulator Direct Acting Spring-Loaded Regulator is designed for a wide range of pressure reduction applications. The regulator offers a great deal of flexibility because it offers a variety of body sizes and end connections, outlet pressure settings, and ...

Introduction: The Fisher/Fisher V500 Eccentric Plug Valve combines the robustness of a ball valve with the high efficiency of a rotary valve. It is designed to control corrosive, coking, and other difficult liquids, providing throttling or on/off operation. 　　Features: Self-centering seat rings ...

Application Flexibility—Actuators can be set either push-down open or push-down shut-off and can be installed anywhere in the four actuator/body mounting positions. Minimized dead zone—single joint connection plus splined pair clamp linkage reduces idling to low and improves control accuracy

The 44-1300 Series is a high-pressure, high-flow pressure reducing valve that offers both bleed and balanced spool designs. The 44-1300 series is available with Cv = 0.8 and 2.0. Chamber-loaded and pneumatically compressed load models are available. Ideal for commercial diving, breathing air, special gas mixture regulation, rigid kit diving...

The Fisher CAV4 valve is designed for clean, cavitation applications with a pressure drop of more than 207 bar (3000 psi). The Cavitrol™ IV trim in the valve is designed to extend the flow area. Each trim stage has a sequentially increasing flow zone. This guarantees a very ...

Complete Fisher pipe silencers provide superior noise reduction performance for applications where valves generate a lot of noise. Once installed, the total system pressure drop is split between the valve and the silencer. This allows the valve to operate at a lower pressure drop ratio, reducing the noise generated during the flow through the control valve.

The Fisher C1 controller and transmitter continues the tradition of durable and reliable manometry equipment when it comes to solving air/gas consumption problems. The C1 meets the needs of durable and reliable pressure measurement equipment. specification Certified ATEX, CUTR Input signal pneumatic Maximum outlet pressure 40 p ...

KTM Mecafrance Series RA three-piece ball valves with oscillating centre section designed for reliable use with easy seat and gasket replacement. The RA series is available with full and reduced boreholes, cast in carbon or stainless steel, and has an ISO top flange for easy automation. Feature: Swing center part ...

Simple installation—The one-piece body flange can be matched with many different types of pipe flanges to meet a variety of pipe requirements. Flanges help reduce exposed pipe flange bolting, shorten alignment and installation time, facilitate safety valve installation, and improve pipe tightness. Clamp valves in the pipeline ...

Fisher CAV III Micro-Flat trims are designed for cleaning, cavitation, and low flow applications with a maximum pressure drop of 241 bar (3500 psi). This product is a combination of two different products: cavitation control with Cavitrol III trims and Micro-Flat ...

The Fisher HP Series Control Valve is a single-port, high-pressure, globe or angle valve with a metal seat, cage guide, and push-down to shut-off plug action. These valves are designed for high-pressure applications in the process control industry, such as power generation, hydrocarbon production, chemical processing, and oil refining. ...