A smooth production process is the policy that every production manager strives to achieve. In order to accomplish this policy, a high-performance automation system is required. With the new handheld bus diagnostic device FDH-1, you will be one step closer to maximizing the availability of your equipment. Its comprehensive monitoring and diagnosis capabilities ensure that you have a solid, high-quality bus physical layer. Here are 5 reasons why the installation and maintenance of bus equipment can be as simple as possible with the FDH-1.
1. Knowledge: Take control of your bus
The handheld bus diagnostic device FDH-1 can be regarded as a more intelligent multimeter. It only takes the push of a button to quickly view any network segment. And it can work independently, making it a great addition to the engineer's toolbox.
2. Coaching: No special training is required to operate
The built-in display screen shows the coaching method for the user. Multilingual dialogs guide you through every task, including fault finding, debugging, and documentation. For both beginners and experienced users, the FDH-1 is an excellent tool.
3. Tip: Get support from the built-in expert system
The new hand-held bus diagnostic device FDH-1 contains an expert system that converts unprocessed measured values into easily identifiable information. It can describe the possible causes of the problem, such as a wiring error, a grounding problem, or a complex environment, and can provide the user with brief instructions for correcting the problem that can be followed.
4. Convenient: You can view the network segment from anywhere
The portable bus diagnostic device FDH-1 does not need to be connected to a computer (PC). It is certified for operation in any bus-related risk area as well as in all explosion-proof maintenance methods. Its battery can work all day long and does not require additional recharging.
5. Quality: make the equipment in the best condition
Even during operation, e.g. after an instrument has been replaced, the FDH-1 can quickly check the condition of the device. And it can actively generate commissioning documents that can be directly signed for.
|
More on that
|
How to deal with the malfunction of the proximity sensor during work
What is the reason for the detection signal when no metal object is close to the switch?
The magnitude of the electromagnetically induced voltage is proportional to the current of the disturbance source, that is, the larger the disturbance current, the greater the disturbance voltage. If the proximity switch does not adopt any ...
|
|
How to use photoelectric sensors – we are blessed
1. Optical adjustment
The factory setting of the sensor is the maximum range, and this setting is subject to change. Note: Only use your finger to press the button.
2. Set the range (when aborted)
Adjust the sensor with a reflector; ...
|
|
Tips and tricks for using sensors – a blessing
Tip 1 – Start with the bus stuff
As a first step, the engineer should use the method of first interfacing the sensor to constrain the ignorance through a bus thing. A bus thing connects to a personal computer (PC) and then to the sensor for I2C, SPI or other ...
|
|
How to install the safety barrier
1. The safety barrier should be installed in a safe place, and the environmental conditions meet the requirements of "application conditions" in the "Safety Barrier Selection Sample".
2. The connecting wires of the intrinsically safe end (blue end) and non-intrinsically safe end circuits of the barrier safety barrier should be laid separately in the wiring slot.
|
|
Common faults and solutions of linear displacement sensors
1. If the electronic ruler has been used for a long time, and the seal is now aged, and there are many impurities mixed with it, and the water mixture and oil will seriously affect the contact resistance of the brush, which will make the displayed numbers keep jumping. At this time, it can be said that the electronic ...
|
|
Test method for sensor output
1. Test for NPN output sensor
The NPN sensor output, also known as OC gate output, is based on the principle of open collector output of a transistor.
The principle of NPN type OC gate output is whether the output of the NPN transistor and GND are short-circuited. When the transistor is turned on, the output and GND ( ...
|
|
The measurement properties of our sensors
According to the nature of the measurement, sensors can be divided into three categories: physical sensors, chemical sensors and biosensors.
Physical sensors: It is the use of certain physical effects to convert the measured energy into energy that is easy to process.
|
|
Analysis of the use of P+F encoders
1. Grating pollution This will reduce the signal output amplitude, and the oil must be quietly wiped off with absorbent cotton dipped in anhydrous alcohol.
2. Encoder connection cable fault: the probability of this fault is high, and it is often encountered in repair, which should be the priority factor. Generally, the encoder cable is broken ...
|
|
How to choose an accelerometer
First, understand the digital output part. When purchasing an accelerometer sensor, you must understand the digital output, because this determines the interface between the system and the acceleration sensor, if the number does not correspond, it is inconvenient to use, so you must understand the data at the time of selection.
|
|
Precautions for the installation of inclination sensors – we are blessed
1. The device mode of inclination sensor is divided into two types: horizontal device and vertical device, but whether it is a horizontal or vertical device, the sensor device surface should be parallel to the face of the measured object when installing, and the influence of dynamic and acceleration should be reduced at the same time.
...
|
|
Precautions for the installation of linear displacement sensors – we are blessed
1. The linear displacement sensor should be used to prevent over-travel in the application, and a certain margin should be left in the selection to facilitate the use of the device.
2. The linear displacement sensor device is fixed by a bracket, and then the follow-up shaft is connected to the moving object to be measured. When the sensor is fixed in the device, it can be ...
|
|
Photoelectric switches for sensors
Photoelectric switches are what we generally call sensors. The definition of the sensor under the national standard GB7665-87 is: the equipment or device that can feel the specified measured parts and convert them into usable signals in accordance with certain rules, generally composed of sensitive elements and conversion elements.
...
|
|
The difference between a temperature and humidity transmitter and a temperature and humidity sensor – we are blessed
Let's start with the conceptual difference, the sensor is a kind of detection equipment, can sense the measured information, and can sense the information, according to the law to change the information into electrical signals or other required information output, in order to satisfy the information transmission, processing, storage, display, recording and manipulation ...
|
|
Introducing the P+F Ultrasonic Technology Series
In industrial use, ultrasonic sensors are characterized by high reliability and versatility. Since the ultrasonic sensor measurement method works reliably in almost all environmental conditions, it is possible to provide a stable connection for object detection or level measurement even in the most chaotic tasks.
...
|
|
Test Methods for Torque Transducers – Beggarbless
In recent years, the use of torque sensors has gradually increased, it can convert physical changes into accurate electrical signals, so what methods can torque sensors go through?
The proven test method of torque sensors is ...
|
|
Inclination sensor application industry – we are blessed
Marine geography
Landslides, avalanches -- Dual-axis skew sensor with liquid level sensor for landslide or avalanche monitoring, through wireless data transmission to the central control system, real-time monitoring of mountain conditions, can effectively reduce the damage caused by landslides.
Construction
...
|
|
The difference between DC and AC contactors – we are blessed
1. The core is different: the core of the communication contactor will suffer eddy current and hysteresis loss, while the DC contactor has no core loss. Therefore, the core of the communication contactor is made of mutually insulated silicon steel sheets, and is often made into an E-shape; The core of the DC contactor is made of a single piece of mild steel, ...
|
|
How to make a load cell
1. Preparation of materials
The materials required for the manufacture of load cells include: thin-film resistors, elastomers, wires and adapters.
Thin film resistor sheet is a thin form of resistor, the internal resistance value of which will coup with the participation of external forces, elastomer is a more malleable ...
|
|
The difference between NPN and PNP photoelectric switches – we are blessed
The difference between NPN type and PNP photoelectric switching sensors lies in the different output levels. NPN outputs low, PNP then outputs high. The type of photoelectric switch is a very specialized technical issue. What are photoelectric switches NPN and PNP? What are their differences?
...
|
|
Material classification for displacement sensors – a blessing
(1) Conductive plastic displacement sensor
Conductive plastic displacement sensor uses a special process to coat the DAP (didipropylphthalate) resistance paste on the insulating body, heat and polymerize to form a resistive film, or press the DAP resistive powder thermoplastic into the groove of the insulating matrix to form a solid body as a resistor.
|
|
Contact
working hours
