How to install the safety barrier

1. Temperature Excessive temperature is one of the common causes of differential pressure sensor failure, as there are many components of the differential pressure sensor that can only function properly within the specified temperature scale. During installation, if the sensor is exposed to temperatures beyond these temperature scales, it may be exposed to ...

In electrical intrinsic safety explosion-proof (abbreviation: intrinsically safe explosion-proof), we generally divide the workplace into explosion-proof area and non-explosion-proof area. There is the transmission of electrical energy between the explosion-proof area and the non-explosion-proof area, for example, the switches, buttons, sensors, etc. in the explosion-proof area are connected to the non-explosion-proof area through the wires.

Direction and fluid flow velocity sensors are essential for different industrial, medical, and environmental uses. Flow sensors quantify the direction and rate of gas and liquid flow in applications such as density measurement, viscosity measurement, flow pattern determination, and wall shear stress determination. In addition to the flow parameters to the direction, ...

1. Single-point load cells should be handled with care, especially for small capacity sensors with alloy aluminum as elastomers, any vibration-induced impact or drop is likely to cause large output errors. 2. Design loading ...

P+F encoders are devices that compile signals (e.g. bit streams) or data and convert them into signals that can be communicated, transmitted, and stored. The P+F encoder converts angular or linear displacements, the former known as the code disc and the latter into an electrical signal. Therefore, the phenomenon: 1, ...

There are several reasons for the formation of zero drift of high-frequency pressure sensors: 1. There are bubbles or impurities in the adhesive layer of the strain gauge 2. The function of the strain gauge itself is unstable 3. There are virtual solder joints in the circuit 4. The stress release of elastomers is incomplete; In addition to the magnetic field, ...

1. Position with the sensor installation boss, and fix it on the metal plate with screws, nuts or pressing plates. When installing the sensor, it is strictly forbidden to turn and drill the shaft and shell to avoid the shaft or shell being subjected to external impact and pressure, and the axial and radial direction of the shaft is not allowed to be subjected to impact force and pressure ( ...

Generally speaking, stainless steel is the base material for most LVDT displacement sensors, as such raw materials have many advantages. Of course, there will be exceptions to the use of raw materials, for example, some products are not so demanding, in order to save costs, different raw materials may be used...

Ultrasonic sensors are used for the inspection of printed circuit boards (PCBs): In this application, ultrasonic sensors are used to inspect printed circuit boards. So what factors need to be considered when installing and installing ultrasonic sensors ...

The air pressure sensor is a control sensor that can be operated according to the barometric pressure end sensing. Inside the air pressure sensor, an air intake tube is provided that can promise air ingress, and once the power is applied, air can be transferred to the inside of the sensor, and when air enters, squeeze sensing occurs ...

1. Proximity sensing. Proximity usually refers to exploration: a. Whether the target exists. The scale or abbreviated shape of an object. Proximity sensors can be divided into touch, non-touch, and imitation. The choice of sensor depends on physical, environmental, and control conditions. Machine...

Resistive strain gauges, elastomers, and detection circuits are the first and foremost parts of the equation. An elastomer is a special shaped structure. It has two functions, firstly, it bears the load of the force on the cell and the external force, to achieve a relatively static equilibrium, and secondly, it ...

1. Self-conditioning. At the beginning of use, please check whether the switch itself is defective and whether the appearance is defective. 2. When using the EL130 photoelectric switch to avoid obstructions, some goods such as colored goods. Less reflective goods. Goods with large gaps between small pieces ...

In order to select the best liquid level sensor, we need to understand not only the characteristics and conditions of the liquid to be measured, but also the advantages and limitations of different detection methods, and then we can select the most suitable sensor. Here are some of the most common inspection technologies on the market today. ...

An encoder is a device that compiles or converts signals or data into signals that can be communicated, transmitted, and stored. The encoder converts angular or linear displacement into an electrical signal. Fault Symptom: 1. The encoder itself ...

First, the first component blocking may be the wrong way of the device, the pressure point is unreasonable, so we often emphasize that the device must be the correct device, once the installation is wrong, maybe the installation is not good, it will bury endless hidden dangers for the back. What are the primary components? Orifice plates, remote transmission measuring joints, etc.

(1) Electronic ruler When the electronic ruler is used to a certain moment, in the face of aging problems, we should pay attention to the fact that if the seal is now aged, and there are many impurities, water mixtures and oil, then it will affect the touch resistance of the brush, resulting in the continuous beating of the displayed numbers.

The rotary incremental encoder outputs pulses when it rotates, knows its orientation by the counting device, and remembers the orientation by relying on the internal memory of the counting device when the encoder does not move or the power goes out. In this way, when the power goes out, the encoder can not have any movement, and when the call is working, the encoder ...

A device that converts the value of a force transducer into an associated electrical signal. Force is the direct cause of changes in the motion of materials. Force sensors can detect tension, tension, pressure, components, torque, internal stresses, and strains. The specific equipment is metal strain gauges, pressure sensors, etc., which have become electric ...

1. Select the type of proximity switch according to the detected object. If the detection object is a metal *** inductive proximity switch, if the detected object is a non-metal such as wood, plastic, paper, water, etc. or a smaller and thinner metal, a capacitive proximity switch should be selected. ...