Bosch Rexroth has launched Sino-Pack 2022

1. Hydraulic pump: Straight shaft swash plate piston pumps are divided into two types: pressure oil supply type and self-priming oil type. Most of the pressure oil supply hydraulic pumps use oil tanks with air pressure, and there are also hydraulic pumps with oil replenishment sub-pumps to provide pressure oil to the oil inlet of the hydraulic pump. The self-priming oil energy of the self-priming hydraulic pump ...

The replacement specification of oil lift piston pump parts, when the various clearances listed are out of tolerance, can be corrected as follows: 1) If the cylinder body is inlaid with copper sleeve, it can be corrected by replacing the copper sleeve. First trim a set of plunger rods to a consistent size, and then polish the outer part with sandpaper of more than 1000#.

1. Cause of failure: the oil level of the hydraulic oil tank is too low; Exclusion method: Add hydraulic oil. 2. Cause of failure: Hydraulic oil is not used according to the season; Exclusion method: Usually suitable for 46# hydraulic oil (or 68#) without special replacement, consider using it when it is cold in the north in winter...

1. The pump device, composed of a motor and an oil pump, is the power source of hydraulic pressure and the "heart", and its role is to convert mechanical energy into the power of the cylinder to realize the lifting of goods. 2. The combination valve is a flat valve installed on the vertical plate, and its function is to adjust the direction, pressure and flow rate of the hydraulic oil.

1. Frequent grease, the electric oil drum pump is running at high speed, and the grease is easy to volatilize, so it is necessary to keep the lubrication at the bearing clean and pay attention to the replacement. 2. Pay attention to the storage of the electric pumping pump should be placed in a dry, clean and no corrosive gas environment. 3. Gear oil ...

1. Check whether the piston pump is damaged and corroded, and replace it if so. 2. Check the fit of the plunger pair. Insert the end of the plunger into the plunger sleeve, tilt it about 60°, and if the plunger can slide slowly under its own action, it will fit well. 3. Check the tightness of the plunger pair. Use...

(1) Remove the burrs from each part. The sharp edge of the gear is poured with natural oil stone, but not into a fillet. The parts after flat grinding should be demagnetized, and all parts should be carefully cleaned with kerosene before they can be put into assembly. (2) Measure and ensure the axial clearance during assembly: Rexroth gear oil pump axial ...

Thanks to the die pad function of the new standard IH04 E standard module from Bosch Rexroth, engineers can use the most common switching systems. These modules are DGUV-tested and certified with a standardized safety concept and are able to meet general safety requirements at the lowest possible cost. Users can optionally set such ...

Bosch Rexroth autonomous mobile robots automate intralogistics and identify the internal roads of the factory themselves The highest level of safety to avoid pedestrians and objects Interactive touch screen for easy operation Compatible with VDA 5050 　　Touch screen and 3D obstacle detection ...

The balancing principle of the balancing valve and its function are explained The principle of balance The TA balancing concept is the concept of total equilibrium, which believes that only after the resistance of the system is adjusted and balanced, can each equipment obtain the design flow under the design operating conditions. Fluid network system for the HVAC industry ...

Simple and easy to use: The product selection is simple and easy, and the debugging can be completed under the guidance Plug & Play: Pre-assembled subsystems, intuitive operating software Rapid start-up: graphical sequencing, direct line integration Partner: ViscoTec dispensing heads are integrated into the software ...

Rexroth vane pump speed selection Rexroth vane pump flow rate and speed linear relationship, relative to low speed screw pump, high speed screw pump can increase the flow and head, but the power is significantly increased, high speed accelerates the wear between the rotor and the stator, must make the screw ...

1. Guiding ideology: 1. The pressure depends on the load oil pump, and the output pressure is inversely proportional to the flow rate. In the state of electronic control, when the external load increases, the system pressure increases, when the system pressure increases, the pressure of the front pump oil flow and the rear pump oil flow into the rear pump increases, and the computer detects the ...

It's hard to imagine a factory automation system without linear robots. The application of linear robots involves handling incoming materials during product production, assembly or packaging, whether integrated into a single machine as a pick-and-place unit or integrated into a semi-automatic or fully automated production line. However...

Rexroth hydraulic pumps: 1. Most users think of a pump as an element that outputs a flow rate at a certain pressure 2. Hydraulic pumps often work at stable and high speeds 3. Generally, it is required that the pump can output high pressure when the rated speed is saved 4. In some applications, the pump is generally only ...

The automotive industry expects more support from suppliers in quality assurance for assembly work. As a result, suppliers in the automotive industry are looking to automation partners to better meet this technology demand while delivering faster. Mechanical engineering companies need more applications in standard tasks ...

Classification and structural characteristics of Rexroth gear pumps 　　According to the form of gear meshing, it can be divided into external meshing and internal meshing. According to the different tooth curves, it can be divided into: involute and cycloid. According to the surface form, it can be divided into spur gear type, helical gear type, herringbone gear ...

1. Rexroth hydraulic piston pump A10VsO series: A10VsO18, A10VsO28, A10VsO45, A10VsO71, A10VsO100, A10VsO140 2. Rexroth hydraulic piston pump A10VO series: A10VO28, A10VO45, A10VO71, A10VO100, A10VO140 3 ...

9. Cause of failure: "left-handed" oil pump is installed with "right-handed", resulting in damage to the skeleton oil seal; Exclusion method: the "right-handed" pump cannot be installed on the "left-handed" machine, otherwise the skeleton oil seal will be damaged; 10. Cause of failure: The hydraulic oil is too dirty. Exclusion Method: Cleaning System, ...

1. Check the internal leakage of the boom cylinder. The easiest way to do this is to raise the boom and see if it has a noticeable free descent. If the drop is obvious, disassemble the cylinder for inspection, and replace the sealing ring if it is worn; 2. Check the control valve. First of all, clean the safety valve and check whether the valve core is grinding.