1. Hydraulic pump:
Straight shaft swash plate piston pumps are divided into two types: pressure oil supply type and self-priming oil type. Most of the pressure oil supply hydraulic pumps use oil tanks with air pressure, and there are also hydraulic pumps with oil replenishment sub-pumps to provide pressure oil to the oil inlet of the hydraulic pump. The self-priming hydraulic pump has a strong self-priming capacity and does not require external oil supply. The hydraulic oil tank with air pressure supply must wait for the hydraulic tank to reach the air pressure before operating the machine after each start of the machine. If the air pressure of the hydraulic oil tank is insufficient, it will cause the pulling off phenomenon between the hydraulic pump and the sliding whip, and cause abnormal wear and tear of the return plate and pressure plate in the pump body. After 3000h of the piston pump for oil supply, the operator needs to check the piston pump 1-2 times a day to check whether the hydraulic pump is running normally. If it is found that the speed of the hydraulic cylinder drops or the car is stuffy, the oil replenishment pump should be dismantled and inspected, and the impeller edge should be checked for scratches and whether the gap of the internal gear pump is too large.
2. For the self-priming piston pump, the oil in the hydraulic oil tank shall not be lower than the lower limit of the oil standard, and a sufficient amount of hydraulic oil shall be maintained. The cleaner the hydraulic oil, the longer the service life of the hydraulic pump.
3. The most important component of the bearing piston pump for hydraulic pump is the bearing, if the bearing has clearance, the normal clearance of the three pairs of friction pairs inside the hydraulic pump cannot be guaranteed, and the hydrostatic support oil film thickness of each friction pair will also be destroyed, and the service life of the piston pump bearing will be reduced.
According to the information provided by the hydraulic pump manufacturer, the average service life of the bearing is 10,000h, and if it exceeds this value, it needs to be replaced with a new port. The dismantled bearing, without professional testing instruments can not detect the clearance of the bearing, can only be used visual inspection, if found that the surface of the roller has scratches or discoloration, it must be replaced. When replacing the bearing, you should pay attention to the English letters and model of the original bearing, most of the piston pump bearings are used in large load capacity bearings, it is best to buy the original manufacturer, the original specifications of the product, if you replace another brand, you should consult the bearing experienced personnel to check the table for replacement, the purpose is to maintain the accuracy level and load capacity of the bearing.
4. Inspection and repair of three pairs of friction pairs: the plunger rod and cylinder bore can be repaired according to the replacement standard of plunger pump parts, when the various clearances of the parts are out of tolerance:
(1) If the cylinder is inlaid with copper sleeve, it can be repaired by replacing the copper sleeve. First of all, trim the diameter of a set of plunger rods to a uniform size, and then polish the outer diameter with sandpaper of more than 1000#. There are three ways to install copper sleeves in the cylinder:
a. Heating and hot charging of the cylinder block or low-temperature freezing and extrusion of copper sleeve, interference assembly;
b. Adopt Loctite adhesive assembly, which requires a groove on the outer diameter surface of the copper jacket;
c. Cylinder bore tapping, copper sleeve outer diameter processing thread, coated with Loctite glue, screwed into assembly.
(2) The repair method of the cylinder block and copper sleeve of the melting combination method is as follows:
a. Repair cylinder bore by grinding rod, manual or mechanical grinding;
b. Adopt a coordinate boring machine to re-boring the cylinder bore;
c. Use a reamer to repair the cylinder bore.
(3) Adopt "surface engineering technology" in the following ways:
a. Plating technology: plating a layer of hard chrome on the surface of the plunger;
b. Brush plating technology: brush and plate wear-resistant materials on the surface of the plunger;
c. Thermal spraying or arc spraying or electric spraying: spraying high carbon martensitic resistance
(4) Most of the cylinder materials without copper sleeves are ductile iron, and amorphous films or coatings are prepared on the inner wall of the cylinder. Because the inner wall of the cylinder bore has this special substance, it can form a hard-hard matching friction pair. If you blindly grind the cylinder bore and grind off the surface material of the inner wall of the cylinder bore, the friction and structural performance will be changed. If the friction pair with the coating removed is forcibly used, the temperature of the friction surface will rise sharply, and the plunger rod will be glued to the cylinder bore
5. In addition, a unique thin film coating is prepared on the surface of the plunger rod, the coating contains the function of anti-friction + wear-resistant + lubrication, this group of friction pairs is actually hard-soft pairing, once the coating is changed manually, it also destroys the friction pair of the best matching material, and repairs these special piston pumps must be sent to professional repair shops.
|
More on that
|
A brief introduction to Rexroth hydraulic motors
A Rexroth hydraulic motor is an actuator of a hydraulic system that converts the liquid pressure energy provided by a hydraulic pump into the mechanical energy (torque and speed) of its output shaft.
Hydraulic motors, also known as oil motors, are mainly used in injection molding machinery, ships, hoists, construction machinery, construction machinery, etc.
|
|
The purpose of using Rexroth proportional valves or servo valves
The purpose of using Rexroth Rexroth proportional valve or servo valve is: to achieve throttling control of the flow rate in an electronic control way (of course, pressure control can also be achieved after structural changes), since it is throttling control, there must be energy loss, servo valve is different from other valves, its ...
|
|
Rexroth Hydraulic Pumps – Routine maintenance and troubleshooting of gear pumps
1. Daily maintenance
1) Strictly implement the post operation method and carefully fill in the operation records.
2) Check the bearing temperature and oil pressure regularly; Check the level height of the lubricating oil every shift.
3) Check whether there is leakage in the sealing part once per shift.
4) Do a good job in each shift ...
|
|
Types and characteristics of Rexroth gear pumps
Classification and structural characteristics of Rexroth gear pumps
According to the form of gear meshing, it can be divided into external meshing and internal meshing.
According to the different tooth curves, it can be divided into: involute and cycloid.
According to the surface form, it can be divided into spur gear type, helical gear type, herringbone gear ...
|
|
Rexroth hydraulic pump - piston pump selection precautions
1. Determine the pressure
The rated pressure of the selected metering pump is slightly higher than the actual maximum pressure required, generally 10-20% higher. Don't choose too high, too much pressure will waste energy, increase the investment and operating costs of the equipment.
2. Determine the flow rate
Selected ...
|
|
Rexroth's view of automation trends: Leading the new trend of automation: freedom and openness for all
· Integrate know-how from all parties through an ecosystem
· Low-code/no-code: Five times faster time to market
· Independence from global supply chains
· Long-term availability
The industrial automation transformation is well underway and will take a big step forward in 2022.
|
|
The difference between Rexroth hydraulic pump and hydraulic motor
Rexroth hydraulic pumps:
1. Most users think of a pump as an element that outputs a flow rate at a certain pressure
2. Hydraulic pumps often work at stable and high speeds
3. Generally, it is required that the pump can output high pressure when the rated speed is saved
4. In some applications, the pump is generally only ...
|
|
Common Causes and Troubleshooting Methods of Hydraulic Pumps(9-16)
9. Cause of failure: "left-handed" oil pump is installed with "right-handed", resulting in damage to the skeleton oil seal;
Exclusion method: the "right-handed" pump cannot be installed on the "left-handed" machine, otherwise the skeleton oil seal will be damaged;
10. Cause of failure: The hydraulic oil is too dirty.
Exclusion Method: Cleaning System, ...
|
|
Bosch Rexroth presents the new Heglon drive, which has been specially developed for rubber machinery
At the International Rubber Congress 2022 in Nuremberg, Bosch Rexroth presents a new Heglon drive specially developed for rubber machinery. It is designed to significantly reduce energy consumption and thus CO2 emissions in daily operations. Similar to traditional electromechanical drives, the pre-assembled ...
|
|
Bosch Rexroth | No need for a control cabinet, a new solution for intralogistics
Less is more: Lean manufacturing is an important competitive factor for manufacturing companies. It's a question of how processes can be optimised so that they can act faster and more flexibly to increase economic efficiency, and the same applies to intralogistics. If the logistics are not properly organized, regardless of the production ...
|
|
How Rexroth hydraulic pumps are adjusted
How Rexroth hydraulic pumps are adjusted
1) Swash plate axial piston variable pump, used for open hydraulic rotation back
2) Mainly used in the field of mobile machinery
3) The pump works under the condition of self-priming, mailbox pressurization or with built-in suction pump, (centrifugal pump).
4 ...
|
|
Rexroth hydraulic pumps – how to choose a hydraulic motor
1. Workload cycle
2. Oil type
3. Minimum flow rate and maximum flow
4. Pressure range
5. System type: open system or closed system
6. Ambient temperature, system working temperature and cooling system
7. Oil pump type: gear pump, ...
|
|
Rexroth solenoid valve can not open the reason analysis and solutions
1) Coil problem
Use a voltmeter to measure the voltage across the coil. This should help you determine if the coil is working properly. You can also gently pull the coil to feel if there is a magnetic force acting on it. If it proves difficult to pull, the coil generates a magnetic field, which creates an excitation.
|
|
A brief introduction and classification of Rexroth hydraulic pumps
Rexroth hydraulic pump is the power component of the hydraulic system, it refers to the oil pump in the hydraulic system, it is the hydraulic component that provides liquid for hydraulic transmission, and it is also a kind of pump. Its function is to convert the mechanical energy of the prime mover into the pressure energy of the liquid, that is, the hydraulic system is ...
|
|
Rexroth launches a safe and reliable remote update service
Progressive optimization of software functions for off-highway equipment requires large-scale remote device updates: The new version of BODAS Connect will provide a solution for this (Image source: Bosch Rexroth AG)
Bosch Rexroth will present a solution for remote updates of off-highway equipment at bauma 2022 ...
|
|
Rexroth Piston Pump FAQs
Rexroth piston pump failure manifests itself as follows.
The causes and elimination methods of excessive working noise of piston pumps.
There is air in the oil pump. This failure usually occurs when a new pump is installed. When opening a new pump, oil should be added to the pump first to lubricate the pump's bearings, plungers, and cylinders.
...
|
|
Rexroth hydraulic pump - what are the precautions for the use of hydraulic pump?
1. The speed and pressure of the pump should not exceed the specified value, and long-term use should be avoided, otherwise the life of the hydraulic pump will be affected.
2. When the hydraulic pump is started, it should be jogged several times, and after the oil flow direction and sound are normal, it should run under low pressure for 5-10min, and then put into normal operation. ...
|
|
Rexroth Hydraulic Pumps - Classification of Piston Pumps and Their Detailed Description
1. Classification of piston pumps
Piston pumps are generally divided into single piston pumps, horizontal piston pumps, axial piston pumps and radial piston pumps
1. Single piston pump
It is mainly composed of an eccentric wheel, a plunger, a spring, a cylinder block and two check valves. A closed volume is formed between the plunger and the cylinder bore. Slanting...
|
|
The Rexroth LinSelect selection tool helps you select Cartesian robots
A new reference process for gluing tasks has been added to the LinSelect configurator
Just enter a few parameters to get specific product recommendations
Complete subsystems for handling and gluing tasks
Thanks to the intelligent reference process in the LinSelect selection software,
...
|
|
Rexroth's leading motion control technology – with innovative packaging that makes it easy
The emergence of "ready-to-shelf cartons" has changed the situation by bringing retailers and consumers closer together with the new carton that combines fast shelf and display. After the goods are delivered to the supermarket, the staff only needs to open the closed boxes on all sides, and the cartons are "immediately" into pallets.
|
|
Contact
working hours
