If the inverter is to run the equipment again after being shelved for more than half a year, the probability of damage may be greatly increased due to many factors such as the placement environment, the service life of the inverter, and the load rate, and the failure usually presents the following problems:
1. After the equipment is energized, the inverter will blow up the machine and the pre-circuit breaker will jump off.
2. After starting, the inverter panel is not displayed
3. The inverter runs normally after starting, but it fails after operation
4. The inverter runs normally after starting, but it appears to be a frying machine after operation
Why is there a phenomenon of inverter failure described above?
1. The improper placement environment of the inverter will lead to the above problems.
2. The inverter is composed of rectifier module, IGBT and electrolytic capacitor and other primary components, during which if the electrolytic capacitor is not energized for a long time, it will cause the electrolyte in the electrolytic capacitor to dry up, so that the capacity decreases and the leakage increases. In this way, when the inverter is powered, the switching power supply operation will be abnormal or damaged, and in serious cases, this will lead to the electrolytic capacitor of the main circuit being damaged, resulting in the explosion of the inverter.
Why do some inverters still work normally after being placed for a period of time?
1. The inverter has a good storage environment
2. The inverter has not been working for a long time under overheat or overload conditions
3. The service life of the inverter is short
4. The capacitance characteristics inside the inverter are relatively good
How to prevent the inverter from powering failure?
1. If the inverter is not used for a long time, it should be sealed and stored in a dust-proof and moisture-proof environment, and the storage temperature is -25C-65C.
2. It is safer and more useful to use special equipment to charge the inverter regularly (once every 3 months) and check the input and output ports. 220 volts are supplied to a 380 volt inverter (110 volts are supplied to a 220 volt inverter) and the voltage slowly rises from 0 volts to 220 volts. The duration is determined according to the power of the inverter. Then, supply 380 volts (220 volts) to the drive and look at the input voltage. Only an imbalance of +/- 3% was promised.
|
More on that
|
Inverter setting method - Delta
The first step is type recognition: acknowledging whether the type of inverter is common to the type of inverter purchased. If not, ask the agent to return the item.
Step 2: Shipping Acknowledgement: After opening the package, check whether the inverter is damaged during transportation. If there is damage, let the agent return ...
|
|
The common sense principle of inverter - Delta inverter
The low-voltage fuse cannot be used as an overload maintenance for the motor.
It is necessary that the additional voltage of the fuse is greater than or equal to the operating voltage of the distribution line.
It is necessary for the additional current of the fuse to be greater than or equal to the additional current of the melt ...
|
|
The importance of harmonic control - Delta inverter
With the rapid development of the electronic and electrical industries, the demand for magnetic materials has promoted the world's huge industrial clusters. In the process of producing magnetic materials, many manufacturers are facing a great dilemma: the production of magnetic materials is mainly controlled by thyristor rectifier furnaces such as bell furnaces and nitrogen rotary furnaces.
|
|
Delta's servo brake circuit wiring method
The wiring method of the braking circuit of the Delta servo is to short the brake resistor inside the driver at the P and C terminals of the Delta servo. The brake of the motor is directly connected to the external 24V drive, which is controlled by an external circuit.
Delta servo is developed according to the needs of customers who use different machinery; Provide a full range of ...
|
|
A brief description of the selection of Delta inverters
Delta's inverter series are as follows:
1：VFD-EL，VFD-S，VFD-L，VFD-C200
Voltage 220V, 380V, power scale 100W-7.5kw
The above series are Delta's simple inverters, commonly known as economical inverters, which are used for small fan pumps, food and medical ...
|
|
Introduction to the features of Delta's power modules
1) Brief planning. Only one battery module, paired with several discrete components, is able to obtain a battery.
2) Shorten the development cycle. It is generally equipped with a variety of input, output, and battery module options. Users are also able to repeat or cross-stack, combined with modular batteries, to complete multi-channel ...
|
|
Regular diagnosis and repair method of Delta servo motor
1. Common faults of motor heating up too high or smoke motor
Causes: 1. Excessive load; 2. Two-phase operation; 3. Blocked air duct; 4. The working temperature is too high; 5. Interphase or inter-turn short circuit fault of motor stator winding; 6. Motor stator winding grounding device; 7. The power supply voltage is too high or too low;
Overhaul...
|
|
The energy-saving principle of inverter - Delta
In order to ensure the reliability of production, all kinds of production machinery are designed with power drive, and there is a certain surplus when designing and matching power drive. When the motor cannot operate at full load, in addition to reaching the power drive requirements, the residual torque increases ...
|
|
Failure analysis of Delta inverter VFD-VL series
Fault 1: Overcurrent in acceleration
Clarification: Overcurrent in acceleration
Solution 1: Check whether the wiring from U-V-W to the motor is poorly insulated;
2: Increase acceleration and deceleration time;
3: Replace the inverter with a larger output capacity;
4: Reduced (P54) torque ...
|
|
Use and maintenance of electric motors - Delta motors
The motor can be started after the work is completed before use, and attention should be paid to the investigation of the motor, transmission device, production machinery and line voltage and ammeter, if there is an abnormal phenomenon, it should be stopped immediately, the fault should be identified and swept away, and then it can be closed and started again.
When the motor is running, ...
|
|
Precautions for the use of transformer DC resistance tester - Delta
The transformer DC resistance tester uses the 32-bit ARM core as the processing center to control the whole machine, actively complete the functions of self-calibration, current stabilization judgment, data processing, resistance value display, etc., and can measure the DC resistance of various types of transformers and transformers.
...
|
|
Precautions for long-term idle use of Delta inverter
If the inverter is to run the equipment again after being shelved for more than half a year, the probability of damage may be greatly increased due to many factors such as the placement environment, the service life of the inverter, and the load rate, and the failure usually presents the following problems:
1. After the equipment is powered on, it becomes ...
|
|
What are the series of Delta inverters?
1：VFD-EL，VFD-S，VFD-L，VFD-C200
Voltage 220V, 380V, power scale 100W-7.5kw
The above series are Delta's simple inverters, commonly known as economical inverters, which are used for small fans and pumps, conveyor belts on food and pharmaceutical machinery, etc., and are used for abbreviated ...
|
|
Description of Delta inverter problems and solutions
Problem Description:
What is stall avoidance?
Solution(s):
If the given acceleration and deceleration time is too short, the output frequency of the inverter changes faster than the motor speed, and the inverter will stop working due to overcurrent, which is called stalling. In order to make the motor ...
|
|
Servo motor speed improvement method - Delta
When many engineers debug servo motors, they often have such a problem: why is my servo motor so slow, how can I improve the speed, and how much can the maximum speed reach? The basis for the confirmation of the speed method of the servo motor: the speed of the servo motor.
...
|
|
Delta servo system composition
The servo system is mainly composed of a servo controller, a drive circuit, a servo motor and the corresponding reaction testing equipment.
(1) Servo motor
Servo motor refers to the motor that controls the mechanical components in the servo system, and the servo motor has an encoder inside, which can respond to the movement in real time.
|
|
Delta launched an integrated control solution for layer winding
As factories move from automation to intelligence, the requirements for equipment performance and scalability are progressing day by day. In response to the rapid development of electronic engineering, transportation and mechanical engineering and other occupations, in order to quickly manufacture related product parts and components, metal coil winding technology is also being carried out at a high speed.
|
|
Precautions for the operation of Delta servo motors
1) The AC servo motor works by means of a dedicated drive. Do not connect the commercial power supply (100/200V, 50/60Hz) directly to the line of the servo motor, otherwise the servo motor will not work properly and the servo motor will be permanently damaged.
...
|
|
Delta's inverter process setting
1. Restore the inverter to factory settings, press the "ENTER" button to enter the parameter setting interface, and press it continuously until it is 00-00 and then stop. Press the number up button to change to 00-02. Press the "ENTER" key again, the panel value will show 0, press the number up key to change it to 9. Press the "ENTER" key, break ...
|
|
Voltage regulator selection method - Delta inverter
1. Capacity safety factor
The AC regulated power supply is based on the output apparent power (kVA) as the nominal rated capacity, and the load is not purely resistive under normal circumstances, that is, the power factor COS¢≠1, and the active power that the regulator can output in practice kW = capacity (kVA) × COS¢. So in the real ...
|
|
Contact
working hours
