Detailed explanation of Yaskawa inverter fault codes

Yaskawa inverter V1000 series has amazing performance, wide range of uses, simple use and maintenance, and user-programmed function, breaking through the previous small inverter in every aspect and improving the level of all small machines. 1 multi-purpose (synchronous motor can also be driven). Detergent ...

1. The cause of the failure may be that the power plug is not plugged in properly. Solution: Check and plug in the power plug. 2. The sensor is damaged and the resistance value is wrong. Solution: Replace the sensor. 3. The fuse is blown out. Solution: Repair and replace the fuse ...

Before starting the machine, you need to check the following items. Machine tools: Confirm that when the four machine tools are empty, the signal sent by the two first-sequence machine tools is the first piece loading signal M28, and the signal sent by the two second-sequence machine tools is the first piece loading signal M28. Robots start with ...

1. Hydraulic coupling mode. That is, a hydraulic coupling device is inserted between the motor and the load in series, and the size of the coupling force between the motor and the load is adjusted by the height of the liquid level, so as to realize the speed adjustment of the load; 2. Cascade speed regulation. The cascade speed regulation must use a wound asynchronous motor, which ...

1. The demand for smart sensors is increasing Quality inspection is a key component in all industries. Analyzing everything from food to phone covers ensures that consumers can trust the goods they receive. Smart sensors enable manufacturers to more efficiently handle this ...

1. Hardware installation @以下操作务必在安川机器人断电状态下执行. 1. Remove the corresponding screws and pull out the bus bracket. 2. Remove the front bezel 3. Insert the DeviceNet substrate and tighten the front plate screws. 4. Insert the board unit as a whole ...

01. The robot switch often jumps or can't close? Cause: 1. Aging of switches; 2. The switch selection is wrong; 3. The pump is stuck or the motor is short-circuited; 4. The line is aging, short circuit, the line is too small or the phase is missing. Solution: Convert the control ...

1. A.00 Absolute value data error: the absolute value data cannot be accepted or the accepted absolute value data is abnormal. 2. A.02 Parameter Destruction: The result of the "sum number check" of the user constant is abnormal. 3. A.04 User constant setting error: the set "user constant" exceeds the set ...

When the Yaskawa inverter fails, the operator will display the fault content, cut off the output, and the motor will decelerate and stop freely. The following is a description of the fault alarm code of Yaskawa inverter and the corresponding fault reason, which is for reference only. OC Overcurrent ...

It is composed of several parts, such as the main circuit, the power supply circuit, the IPM drive and protection circuit, and the cooling fan. Its structure is mostly in the form of units or modulars. Due to the incorrect use method or unreasonable setting environment, it will easily cause the inverter to malfunction and malfunction, or can not meet the expected ...

As we all know, the traditional material removal work is done manually, the cost is high, the efficiency is low, the accuracy of the parts is greatly affected by the manual, and the safety of workers is not effectively guaranteed, so what can be done to effectively solve these problems? Today, I will take you to understand the machine ...

First, the servo dispute settings are too large, and it is recommended to readjust the servo parameters manually or automatically. Second, make sure that the initial value of the time constant of the velocity feedback filter is set to zero, and try increasing the initial value. Thirdly, the electronic gear ratio setting is too large, it is recommended to restore ...

1. Specifications and parameters of the motor The inverter drives the motor during use, so the inverter can be selected from the perspective of the motor to select the model and specification. First of all, we must first understand the specifications and parameters of the motor. You can use Yaskawa inverter ...

(1) Open modular control system architecture: using distributed CPU computer structure, divided into robot controller (RC), motion controller (MC), optoelectronic isolation I/O control board, sensor processing board and programming teaching box, etc. The Robot Controller (RC) and the programmed teaching pendant are connected via a string...

1. If the fault code on the Yaskawa servo drive is UV1, it means that the low voltage of the main circuit is lower than the low voltage standard of 200V, at this time, we need to check whether there is a problem with the wiring of the power supply; 2. If the ...

1. It may be that the capacity of the servo unit does not match the capacity of the servo motor. 2. It may be that the servo unit is faulty. 3. It may be outside the range of parameter settings. 4. It may be that the set value of the electronic gear ratio is outside the set range. ...

First, the correct boot steps: Yaskawa robot 1. Turn on the power switch of the transformer and press the power [start] button. 2. Turn on the [power switch] of the control box, and press the [servo button] according to the prompts on the screen of the instructor 2. Simple operation of the robot ...

1. It occurs when the power is turned on It's a servo unit fault 2. On servo on is happening It is an abnormal wiring of the motor (there is a connection problem or there may be a wrong wire, I encountered a wrong phase) 3. The encoder wiring is abnormal Servo unit failure 4. Re-enter the finger ...

1. First of all, connect the terminal block of Yaskawa servo B1B2, in which the B1 terminal receives the power supply and the B2 terminal receives the signal; 2. Then, connect the terminal block of Yaskawa servo B1B2, wherein B1 terminal receives power supply, and B2 terminal receives signal; 3. After the wiring is completed, ...

1. Hydraulic drive system Because hydraulic technology is a relatively mature technology. It has the characteristics of large power, large force (or moment) to inertia ratio, fast response and high response, and easy to realize direct drive. It is suitable for working in large load-bearing capacity, large inertia and solder-mask environments.