Examples of applications for ifm inductive sensors in the industry

On November 18, 2008, the 19th Multinational Instrumentation Conference and Exhibition was held in Beijing International Exhibition Center, at the exhibition, as one of the world's leading manufacturers of electronic sensors in the field of industrial automation, Germany ifm electronics showed its advanced sensors and their corresponding ...

Incremental sensors Only the bearing change information is provided so that the practice bearing is unknown at startup. Each time the index/symbol signal is used to say the zero or zero bit of the device. Detected in the homing procedure. For the commutation of brushless motors, the motors usually have three magnetic Hall sensors, which are ...

(1) When the strain limit increases with the strain, the nonlinearity of the output of the strain equipment increases, and the error reaches 10%, the strain limit of the strain equipment is general. (2) After the mechanical hysteresis sensitive grid, subbase and adhesive layer are subjected to mechanical strain, they will generally ...

1. According to the measurement object and measurement environment In order to carry out a detailed measurement operation, it is necessary to consider the principle of the sensor first, which needs to analyze many factors before confirmation. Because, even if the same physical quantity is measured, there are sensors with multiple principles to choose from.

Load cells are an important category of load cells, the most widely used, and there are many ways to do so. In general, the composition of load cells is mainly elastomers, strain gauges, seals, etc. Several of them interact with each other to affect the function of the sensor, and their respective roles are as follows: ...

1. ifm controller CAN parameters: communication cycle In some applications, it is possible to set the monitoring time for SYNC packets generated by the master here. Note that this moment is larger than the SYNC moment of the master. To go through the experiment ...

Spindle speed detection In order to prevent damage to wind turbines due to overspeeding, the rotational speed is detected using inductive sensors and evaluated by safety-related speed monitors. ifm IFS24X series inductive sensors with M12 ...

There are two kinds of proximity switches: NPN output type (current inflow) and PNP output type (current outflow), when the current outflow sensor (PNP output type) is turned on, the current flows from the power supply to the load through the output terminal of the sensor, enters the load, and then flows to the connection.

A differential pressure sensor is a sensor used to measure the difference between two pressures, usually used to measure the pressure difference between the front and rear ends of a device or component. A typical application of differential pressure sensors is to measure the difference in exhaust pressure between the front and rear channels of the exhaust particulate trap of a passenger car engine.

Accelerometers are the most important element in engineering vibration measurement. In the test system, the sensor is the first link of data acquisition and profiling, so the selection and correct use of the sensor will directly affect the quality and accuracy of the measured signal. Although people working on engineering vibration know that this ...

Sensor detection is known to prevent disturbances. Once disturbed, the sensor may be damaged, the measurement system will be affected, the inaccurate data will affect the future use, the judgment will be biased, and the impact can be large or small, so anti-interference is very important. Today we're going to comment ...

ifm has the widest range of IO-Link sensors on the market. The new RFID antenna further completes the original product variety. The RFID antenna is planned to connect to the IO-Link master. The master* can supply up to 8 M12 sockets for easy connection to IO-Link RFID antennas. IO-Link Master ...

1. If the electronic ruler has been used for a long time, and the seal is now aging, it is mixed with a lot of impurities, and the water mixture and oil will seriously affect the contact resistance of the brush, which will make the displayed numbers constantly beat. At this time it can be said that the electronics of the linear displacement sensor ...

The first point is that photoelectric sensors and fiber optic sensors work differently First of all, from the principle of operation of the two, first of all, the photoelectric sensor is operated according to the principle of the photoelectric effect, that is to say, when the light hits the photoelectric sensor made of semiconductors, the light will be announced.

The aluminum foil sensor is composed of elastomer, strain gauge, adhesive, maintenance layer, compensation circuit, etc. The strain transmission path is: elastomer - + adhesive → strain gauge sensitive grid - + overlay - maintenance coating, which constitutes a complex system that is more different from the strain gauge itself. If the application attached to the elastomer ...

Ifm flow sensors ensure safety Specially developed for monitoring the fresh air and exhaust of machines Optimized performance is achieved through special air conditioning Rugged probes for demanding applications 2-in-1: Flow rate and temperature ...

1. ifm sensor PN2071 pressure up, sensor output can not go up in this case, first should check whether the pressure interface is leaking or blocked, if you admit that it is not, check the wiring method and check the power supply, if the power supply is normal, then simply pressurize to see if the output changes, maybe observe ...

1. According to the connection form of the shaft and the length of the dynamic torque sensor, confirm the interval between the prime mover and the load, adjust the separation of the axis of the prime mover and the load relative to the reference plane, so that the coaxiality of their axis is less than Φ 0.03mm, and fix the prime mover and the load on the reference plane. ...

Conceptual understanding of sensors The sensor is a kind of detection device, which can sense the measured audio, and can convert the perceived audio into an electrical signal or other required audio output according to the inevitable discipline, so as to satisfy the transmission, disposal, storage, display, recording and control of the audio.

Temperature sensor 1. The sensor should be firmly grounded, and the wire side of the sensor should not be short-circuited. 2. The thermistor of the moving magnet water thermometer sensor will increase with the temperature and the resistance value will decrease. Fuel level sensor ...