Precautions for the use of resistive load cells – ifm

Not all damaged bearings can be corrected, but the cause and extent of the damage to each damaged bearing must be evaluated to prevent or reduce further damage before considering the correction or replacement of a new bearing. There are many reasons for bearing damage, such as improper equipment, dirt invasion, etc.

1. Start with the bus east and west As a first step, the engineer should take the approach of first interfacing the sensor, which is through a bus stuff to constrain the ignorance. A bus thing connects to a personal computer (PC) and then to the sensor for I2C, SPI or other ...

Ifm flow sensors ensure safety Specially developed for monitoring the fresh air and exhaust of machines Optimized performance is achieved through special air conditioning Rugged probes for demanding applications 2-in-1: Flow rate and temperature ...

Easy-to-install sensor with long-service life electronic GMR unit – flush unit This sensor can be conveniently installed in a C-slot Fixed at the end of the housing for stable elastic stress relief Multiple articulations ...

Thanks to a uniquely adjustable sensor, it can be flexibly adapted even in wet environments ●After touching the sensor, the ergonomic plan is selected for work ● Open delay can prevent unintentional opening ...

ifm has the widest range of IO-Link sensors on the market. The new RFID antenna further completes the original product variety. The RFID antenna is planned to connect to the IO-Link master. The master* can supply up to 8 M12 sockets for easy connection to IO-Link RFID antennas. IO-Link Master ...

1. Resistance strain gauge The resistance strain gauge is a resistance wire mechanically distributed on a substrate made of organic materials, that is, it becomes a strain gauge. An important parameter for him is the sensitivity coefficient K. When his ends are subjected to the F force, they will elongate, that is, they will be deformed. ...

1. High sensitivity. The strength of the detected signal is getting weaker and weaker, which requires a significant increase in the sensitivity of magnetic sensors. The use includes current sensors, angle sensors, gear sensors, and space environment measurement. 2、 ...

Gas detector is an instrumentation tool for gas leakage concentration detection, which mainly uses sensors to detect the types of gases present in the environment, and gas sensors are used to detect the composition and content of gases. Many environmental factors can affect gas detector sensing ...

Selection of sensitivity In general, within the linear scale of the sensor, the higher the sensitivity of the sensor, the better. Because as long as the sensitivity is high, the value of the output signal corresponding to the measured change is relatively large, which is conducive to the signal processing.

ifm precision pressure sensors with additional temperature monitoring output via IO-Link and 2 switching channels for continuous transmission of process values and advanced diagnostic information in a housing width of only 19 mm ● 2 solutions: ...

Capacitive sensors can detect any object without touch. In contrast to inductive sensors, which can only detect metals, capacitive sensors are also capable of detecting non-metallic materials. principle 1. The first thing to be measured is ...

1. The ifm controller has a control function Another important reference feature for the purchase of ifm controllers is the ability to control movements and other applications. Fulfillment of these functional requirements requires I/O, as well as a strong processor and the ability to prioritize missions. Programmable Drum Switches (PDS...

Diagnose sensor faults based on mathematical models? When there is a problem, the first time is to diagnose it, see where the problem is, so that it is easy to deal with, from different angles, we use more than one method when diagnosing the problem, if this is classified, it can be divided into two ...

1. After the wireless sensor device is installed, it appears to be beating or the number is inaccurate Reason: There is electromagnetic interference on the site, or the signal line and the power line go to the same trunking. Solution: The product function selected by the customer does not meet the on-site working conditions, and it needs to be installed or replaced.

Amperometric gas sensors operate by reacting with the measured gas and generating an electrical signal proportional to the gas concentration. A typical amperometric gas sensor consists of a sensing electrode (or working electrode) and a counter electrode, separated by a thin electrolytic layer. The gas passes through a porous membrane ...

1. The ifm controller has a control function Another important reference feature for the purchase of ifm controllers is the ability to control movements and other applications. Fulfillment of these functional requirements requires I/O, as well as a strong processor and the ability to prioritize missions. Programmable Drum Switches (PDS...

The TCC temperature sensor was unanimously recognized by the jury and won the Red Dot Design Award 2020 for its cost-effective solution with its excellent design, ideal cleaning performance and high-quality materials. ifm TCC ...

The depth of the internal thread of the installation with the sensor should be greater than the length of the external thread of the sensor itself, so as to avoid the sensitive diaphragm of the sensor pushing to the bottom of the internal thread, so that the sensor is affected by stress. If the size of the internal thread has been ...

1. Inspection interval Detect the stop, start and orientation of elevators and lifting equipment; Detect the orientation of the vehicle to prevent two objects from colliding; Detect the setting orientation of the operating machinery and the limit orientation of the moving machine or components; Detect the abort azimuth of the rotary body, the opening or closing of the valve; Detection of pneumatic or hydraulic cylinders ...