Autonex TR1D series temperature controller features

1. Check the standard of the equipment hole: Assuming that the standard of the equipment hole is not suitable, some of the threads of the sensor will be slightly worn during the equipment process. This not only affects the sealing performance of the equipment, but also makes the pressure sensor inadequate, and may even cause safety hazards. ...

Infrared sensors include an optical system, a detection element, and a conversion circuit. Optical systems can be divided into two categories: transmissive and reflective according to different structures. According to the working principle, the detection element can be divided into thermal detection element and photoelectric detection element. The most widely used thermistors are thermistors. Thermistor...

The TR1D series has a high-speed sampling period of 50ms and a display accuracy of ±0.3% for more accurate temperature control. Simultaneous heating/cooling control is available to provide effective temperature control. With a width of only 22.5mm, the product minimizes the limitation of installation space and can be accessed with ...

1. After the modulation pulse generated by the vibration circuit passes through the reflection circuit, the digital integration photoelectric switch or RC integration method is used to eliminate the disturbance, and finally the driver is triggered by a delay (or no delay) to output the photoelectric switch control signal. 2. Use optical elements to make the beam in the middle of the propagation medium.

Proximity switches are the most commonly used solution for touchless detection. The most commonly used proximity sensor is inductive, that is, through electromagnetic waves, to sense metal objects near the detection surface of the sensor; In practice, this is a very simple tool for the detection of metal objects from one to two inches.

1. Percussion hand pressure method It is common to encounter the phenomenon of good and bad operation of the instrument, and most of this phenomenon is due to poor contact or virtual welding. In this case, percussion and hand pressure can be used. The so-called "percussion" is to ...

1. When the working conditions of the exterior are changed (such as changing the medium, changing the ambient temperature, etc.), the zero position of the exterior should be adjusted from the beginning. At the same time, the outer surface of the catheter must be leveled and calibrated with a spirit level. Failure to do so will increase the effect of the change in operating conditions on the zero drift. Rack ...

1) The detected object should not touch the proximity switch, so as not to damage the proximity switch due to friction and bumping; 2) Pull the lead wire of the switch by hand will damage the switch close, and it is best to fix the lead wire with a line card at 10 cm away from the switch when the device is installed.

The pressure sensor in the servo press is built-in, which can ensure that the force on the spindle is not affected by the radial separation force, avoid part of the load in the installation, do not directly connect the workpiece, and is not easy to damage. High-speed rings of ...

The SFN series of safety non-touch door switches reliably monitors the opening and closing of dedicated actuator doors by means of magnetic detection. This product can be connected to up to 30 units through a dedicated controller, and it can be used vertically and horizontally according to the installation environment, which improves the ease of use. ...

Depending on the resolution supported by the encoder, encoders can be divided into marker encoders, HD encoders, and Full HD encoders. The higher the frame rate, the clearer the video. 1. What does the resolution of the encoder mean? The resolution of the encoder refers to the encoder passing through a line or a dark line (also ...

1. Measurement of action interval; When the action piece approaches the sensing surface of the switch from the front, the interval between the action of the switch is the interval between the action of the switch, and the measured data should be within the parameters of the product. 2. The Liberator ...

On September 17, 2019, the 15th MM. New Automation Forum in 2019 with the theme of "Interconnection, Integration and Synergy" was successfully held in Shanghai.

Cover the safety light curtain with your hands and observe whether the indicator light conversion is normal. During the use of the punch photoelectric protection device, the orientation of the photoelectric protection device shall not be changed at will. In the protection zone, block the light curtain by hand, ...

When choosing a pressure sensor, we should consider his inductive accuracy, and what are the aspects that affect the accuracy of the pressure sensor? In fact, there are many factors that form sensor errors, and let's pay attention to four unavoidable errors, which are the initial errors of the sensor. ...

Cover the safety light curtain with your hands and observe whether the indicator light conversion is normal. During the use of the punch photoelectric protection device, the orientation of the photoelectric protection device shall not be changed at will. In the protection zone, the light curtain should be blocked by hand, and the machine should be able to stop the operation immediately. ...

Autonics continuously improves the product function and quality, so that the product is at the international first-class level. For more than 10 years, the market share of the products in Korea has been maintained. 1. Adopt self-developed special IC ...

With the strong support of our customers, Autoniks was selected as one of the "Top 300 World-Class" enterprises by the Korea government for the first time in the industrial control industry. The Korea government's selection of "Top 300 World-Class Enterprises" is an increase in the number of choices ...

Modular power supplies are power supplies that can be mounted directly on a printed circuit board and feature power supply to application-specific integrated circuits (ASICs), digital signal processors (DSPs), microprocessors, memory, field-programmable gate arrays (FPGAs), and other digital or analog loads. One...

Dual PID auto-adjustment function There are high-speed response modes and slow reaction modes in the PID function. When you want to reach the desired value quickly, use the high-speed mode (PIDF mode) When you want to minimize overshoot, use slow mode (PIDS mode) ...