The GOT widescreen family has been expanded with the GT2512

1. The digital-to-analog converter is a system that converts digital signals into imitation signals, which can generally be completed by low-pass filtering. The digital signal is decoded in the first line, that is, the digital code is converted into the corresponding level to form a stepped signal, and then the low-pass filter is carried out. According to the signal and system ...

Torque control: Torque control is based on external simulation imitation typing or direct address assignment to set the output torque of the motor shaft. For example, 10V matches 5Nm. When the external simulation simulation is set to 5V, the output of the motor shaft is 2.5Nm. If the load of the motor shaft is less than 2.5Nm, then when ...

1. Press the motor start button, and the motor will start and run at the corresponding speed of 5Hz; After the delay of 10s, the motor will run at the speed corresponding to 10Hz, and after the delay of 10s, the motor will continue to speed up and run at the speed corresponding to 20Hz; In the future, every 10s, the speed law changes, a ...

1. Hardware (1) I/O channeling, the PLC automatically detects the I/O fault and enters the STOP mode. (2) The I/O is damaged, and the program runs to the response signal that needs the I/O, and cannot execute the instruction downward. (3) Expansion module (functional, such as A/D) ...

In the PLC control system, the content that needs to be displayed mainly includes timer value, counter value and data register value, and the data display method can be summarized into two fundamental types: one is based on the PLC data communication interface, such as RS-232, RS-485/422, and the display device also has such an interface.

1. Overvoltage maintenance The output of the motor inverter has the function of voltage detection, and the inverter can actively adjust the output voltage so that the motor does not bear the overvoltage. Even if the output voltage adjustment fails and the output voltage exceeds 110% of the normal voltage, the inverter will stop to maintain the motor.

1. Press the mode button continuously until you enter the parameter writing state, and the LED display is: Pr.O 2. Press the upper button to adjust the parameter to the Pr.34O parameter. 3. Press SET, the LED displays the initial value of Pr.340, press ...

1. Occasions with brake servo motors: The servo motor is mainly loaded by the motor shaft, assuming that the load driven by the motor shaft is vertical, after the whole control system is powered off, the load on the servo motor shaft will be driven to run down under the action of gravity, so that ...

1、AL. E6 - indicates servo emergency abort. There are generally two reasons for this shortcoming, one is that the 24V power supply of the control circuit is not connected, and the other is that there is no connection between the EMG and SG of the CN1 port. 2. AL.37 - parameter abnormality. The internal parameters are chaotic, and the operator may set the parameters by mistake or drive ...

The tension controller can be called the tension manipulator, which is generally equipped with magnetic powder brake, magnetic particle clutch and tension detector, and is suitable for winding, unwinding, tension control, etc. It also has the so-called manual control function, which generally refers to the ability to give a certain amount of output through the tension manipulator ...

[Example] a motor is equipped with an optical encoder (the optical encoder is coaxially installed with the motor), and the FX2N-32MT is used to measure the speed of the motor. 【Solution】 Because the photoelectric encoder is coaxially installed with the motor, the ...

It has become an irreversible trend to drive the motor through the inverter, and in the actual application process, because the matching relationship between the inverter and the motor is not very reasonable, it often leads to some problems. When selecting an inverter, you should fully understand the load characteristics of the equipment driven by the inverter. Ms. Ginseng ...

Generally, there are three types of Mitsubishi PLC output circuit methods, namely: relay output type, transistor output type and thyristor output type. So what are the characteristics of each of them? First, the relay output circuit Use of relays ...

Control requirements: press and hold the forward rotation button, the servo motor rotates forward, release the forward rotation button, and the servo motor aborts the work. Press and hold the rotary button, the servo motor rotates, release the rotary button, and the servo motor aborts the work. When turning forward, pressing the turn button has no effect. When turning, pressing the forward turn button is invalid ...

In some cases, when the user first touches the use of the Mitsubishi servo motor, it may appear that the Mitsubishi servo motor is not self-locking after it is ready! So, what is the reason for this? And how to deal with it? ...

The PLC control cabinet is the final level of equipment in the power distribution system. It mainly protects, supervises and controls the entire circuit, which is convenient for unified management. The power distribution cabinet is a kind of equipment that can reasonably distribute electrical energy and make the circuit easy to open and close. But because it is a circuit device, the requirements for the level of safety protection ...

Mitsubishi Electric Automation Corporation has launched the A800 Series Integrated Inverter Drive (VFD) for fast, reliable, easy-to-use, and easy integration and installation for occupational demand drives. The A800 series variable frequency drive combines traditional induction and permanent magnet vehicles into a single solution that supplies ...

In GX Works3, there are three types of security settings: block password, security key, and file password. The block password is for the program to prevent others from reading and writing changes, only for the program; The file password is for the PLC to prevent others from reading and writing changes. Security keys are both capable of ...

Mitsubishi PLC is composed of power module, CPU module, input module, output module and substrate. Power module: Provides DC5V power supply for each module on the substrate. CPU module: It is the heart of the PLC. The CPU module consists of ...

01. Base system problem In Mitsubishi PLC, there are binary, octal, decimal, 10, 2-10 (BCD), etc., we need to master the conversion of 2-8 base. 2-8, remember the binary number from the back, divide every 3 into a group, and each group is converted into octal respectively, such as 1 ...