The steps of Weiluntong touch screen CMT to MT copy screen

1. Touch failure; 2. Touch the glass plate is broken; 3. The key is damaged and the key is not effective; 4. White vertical bars, horizontal bars, and bright lines appear; 5. Half can be touched, half can not be touched; 6. Can't enter the program; 7. The touch screen cannot be calibrated.

When using the Weiluntong touch screen, how to set the IP address Examples: CMT2109X2 and CMT2079X First of all -> click on the little yellow button on the touch screen Secondly -> Click on the lock symbol Again-> Enter the password by default 111111 And then-〉 ...

1. MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Second, MT500, this model is the successor of the previous model, after the launch of the very good sales results. ...

1. Check the user manual or technical manual of the touch screen to understand the menu settings and operation methods of the touch screen of this model. 2. Try pressing other buttons or areas on the touchscreen to see if you can enter the menu settings interface. 3. If you are using third-party software or ...

Four-wire: Because of factors such as cost and mature technical level, four-wire touch screen is almost the most basic production specification for touch screen practitioners. First of all, in terms of resistive touch screen technology, four-wire touch screen accounts for more than 50% of the market. It is composed mainly ...

Model 1, MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Model two, MT500, this model is following the previous model, after the launch of the very good ...

1. First of all, open the Weiluntong touch screen and enter the application. 2. Secondly, select "Edit" → "Personalization" on the control bar of the window. 3. Finally, set the picture to the bottom layer. ...

1. High stability, not affected by time and environmental changes 2. Strong adaptability, not subject to current, voltage and static interference, suitable for some harsh environmental conditions (explosion-proof, dust-proof) 3. High light transmittance, no intermediate medium, up to 100% 4. Screen and ...

1. Dispose of dirt and grease on the touch screen The accuracy of the screen is a characteristic of grease build-up on the surface, which can make it cumbersome to type the correct commands. In addition, due to the accumulation of dust caused by overheating, the internal components of industrial computers may not work properly. The use of microfiber ...

EasyBuilder Pro is a very easy to use and powerful Veruntong touch screen programming software, the software provides a humanized human-computer interaction interface, which can meet the needs of different programmers, suitable for Veruntong eMT, cMT, iE, MT (iP) and TK (iP) models, the software provides ...

1. The inverter burns out 2. The fuse will be burned when the power is on, and the motherboard will fail; 3. The liquid crystal is faulty, and the motherboard is also burned; 4. The power supply of the motherboard is partially damaged; 5. The motherboard is faulty, and there is a large current burnout; 6. The backlight does not light up, and the motherboard inverter is faulty; 7. Reverse ...

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

1. The memory address is different. The memory address of the PW touch screen uses the local hold register, while the memory address of the RW uses the hold register index to send RWI. 2. The address range is different. The address range of the LW of the touch screen is 0 to 524287, while the address range of the RW is 0 to .

1. DIP switch mode touch calibration and system initialization. For the full eMT series, MT8000i series, TK series, WT series and other HMIs, there is a set of reset buttons and DIP switches, which can trigger the corresponding functions when switching between different modes. If the HMI touches ...

1. Software editing-system parameter setting-HMI attributes-port number: 8000 change, such as 9000; 2. Bring up the computer task manager - end com_e30.exe under the process; 3. Restart the computer; 4. Query other occupancy on the computer through TCPview software.

1. The touch all-in-one machine can carry out the dynamic display of the three-dimensional model of the object, and has a good interactive experience function. The audience can operate by themselves through the touch all-in-one machine, and "touch" the object at zero distance on the screen, and the audience can also rotate and zoom in arbitrarily on the touch all-in-one screen.

1. Check that the power cord is plugged in and if there is electricity. If there is no electricity, you can replace the cord or plug. 2. Check if the power switch is on. If it doesn't turn on, you can try turning on the power switch. 3. Check if the battery is charged. If the battery is low ...

1.1 How to delete the job button on the taskbar of the touch screen? Set "Modify/Set System Parameters/General/Job Buttons/Features" to "Closed". 1.2 What does RS485 Default/RS485 2W/RS485 4W Separation mean in the communication port type? r ...

1. TK series (simple and practical, widely used) 1、TK8071iP 7" TFT display 800*480 dots, brightness 350, contrast ratio 500:1, 16M color, 128MB memory, DC10.5——28VDC power supply, four-wire resistive type, overall dimensions 200.4*146.5*34m...

Due to the technical limitations and different equipment environment, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the touch screen also needs regular maintenance like ordinary machines, and because the touch screen is a touch all-in-one machine with a high degree of integration of a variety of electrical equipment, so in ...