The inspection method of Weiluntong touch screen slow response

4. Use Fault 4.1 What should I do if the newly purchased touch screen downloads the programmed program and it cannot be touched or the touch freezes? First of all, hit the No. 2 DIP switch on the back of the screen to the direction of on, and then power on to see the copyright of the last line of the screen.

Right-double-click the parameter settings button. Specific steps: 1. Create a new screen, and then make a keyboard, and the OK button is [Screen Jump Control] 2. Double-click the [Parameter Setting] button and select [Properties]. 3. Click [Security], and then ...

To change the IP address of the touchscreen, you need to click the arrow below the touchscreen. Then enter the original password of the touch screen in the pop-up interface: 111111. After that, enter the IP setting interface. Enter the interface to set the IP address you want to set, and finally remember to click after setting ...

Due to technical limitations and poor environmental adaptability, especially the surface acoustic wave screen, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the Weilun touch screen also needs regular maintenance like ordinary machines. And because the Weilun touch screen is a variety of electrical equipment...

When the system setting password of Verun Tong touch screen hardware is lost, the factory settings can be restored by the system initialization method. There are four ways to enter the touch calibration of the touch screen of Veruntong, and the initialization of the operating system can only be carried out through the DIP switch. 1. DIP switch mode touch calibration ...

1、eMT3120A 12.1" TFT display 1024*768 dots, brightness 500, contrast ratio 700:1, 16.2M color, 256MB memory, DC19.2-28.8VDC power supply, four-wire resistive, SD card slot, support SD/SDHC, USB Host USB 2.0 ...

Model 1, MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Model two, MT500, this model is following the previous model, after the launch of the very good ...

Sometimes we need to monitor and change the program of PLC equipment, and when it is inconvenient to connect to PLC or there is no communication line, we can choose to achieve it through the penetration function of the touch screen. The traversal communication function consists of the following two modes: Ethernet When using [Ethernet] ...

1. When turning on and off the power of the machine, it should be operated in strict accordance with the regulations; 2. According to the severity of the environment, set a time limit to open the machine head to clean the reflective stripes and inner surface of the touch screen; 3. At present, the mainstream industrial display program does not have a mouse cursor, because the flashing of the cursor will ...

1. The optical performance is the best. The clarity and light transmittance are the highest, the reflection is the least, and there is no color distortion, this is because the sound wave screen body is pure glass, unlike the resistive screen with multiple layers of composite film; The capacitive screen is coated with a layer of film on the surface, and the light transmittance is worse. 2. Anti-scratch and anti-barbaric use ...

Weiluntong contact screen repair 　　The first step in troubleshooting a touchscreen system is to determine if the problem is related to the display, software, or hardware: Don't confuse the visibility issue with the contact screen issue, the two are unrelated. Software problems are caused by fundamental hardware functions ...

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...

(1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when correcting the position. Solution 1: Recalibrate the position. Phenomenon...

cMT3151 can be stored in the form of data streaming, avoiding the SD card or USB when storing data due to falling off and unable to produce a complete storage record; At the same time, the abnormal operation of the machine is recorded, and the user is assisted in tracking and analyzing the source of the problem. cMT-iPC15 Built-in Error Correction Code (ECC) ...

MT(iE) Series (High Performance) 1、MT8102iE 10.1" TFT display 1024*600 dots, brightness 350, contrast ratio 500:1, 16.7M color, 128MB memory, DC19.2-28.8VDC power supply, four-wire resistive, Ethernet Interface/USB Host...

1. Observational method As the name suggests, it is to use the eyes to visually check whether the components are burned, damaged, deformed, discolored, cracked, and whether the CRT filament is lit after the current is turned on.

1. First of all, open the Weilun touch screen to modify the software, and be sure to choose the software corresponding to the type of touch screen; 2. Modify the required touch screen screen; 3. Then open the "System Settings" button under the "Common" menu in the upper left corner; 4. Set the pop-up window in the system ...

1. Enter the Weiluntong touch screen setting interface, find the input method option, and change it to the corresponding text type (such as Chinese Simplified, English) to solve the problem. 2. Install the corresponding input method, which can also solve this problem. ...

1. Check whether the power supply of the host is working normally. First, check whether the host system is powered by checking whether the power indicator on the host chassis panel is on and whether the power supply fan is rotating. Secondly, use a multimeter to check whether the external voltage meets the requirements, the voltage is too high or too ...

1. Open the Weiluntong editing software, and click Event Login in the pop-up menu bar on the right. 2. On the edit page of event login, we click the new button below, and then a setting page for alarm login will pop up.