What is the reason why the touch screen cannot be turned on after restoring the factory settings?

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

With the promotion of Industry 4.0, human-machine interfaces are commonly found in various types of smart applications. Increasingly complex human-machine applications, from data collection and analysis to system monitoring, often require a large number of logical operations to be realized, which is time-consuming and difficult to maintain. 　　Wei Lun Tong ...

1. Software use issues 1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4 ...

1. MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Second, MT500, this model is the successor of the previous model, after the launch of the very good sales results. ...

1. When turning on and off the power of the machine, it should be operated in strict accordance with the regulations; 2. According to the severity of the environment, set a time limit to open the machine head to clean the reflective stripes and inner surface of the touch screen; 3. At present, the mainstream industrial display program does not have a mouse cursor, because the flashing of the cursor will ...

When the system setting password of Verun Tong touch screen hardware is lost, the factory settings can be restored by the system initialization method. There are four ways to enter the touch calibration of the touch screen of Veruntong, and the initialization of the operating system can only be carried out through the DIP switch. 1. DIP switch mode touch calibration ...

1. TK series (simple and practical, widely used) 1、TK8071iP 7" TFT display 800*480 dots, brightness 350, contrast ratio 500:1, 16M color, 128MB memory, DC10.5——28VDC power supply, four-wire resistive type, overall dimensions 200.4*146.5*34m...

3.1 What should I do if the touch screen shows garbled characters? Select "Oriental Language" in the EB500 software "Options/Language Selection", and then compile it after saving it so that there will be no garbled characters. 3.2 Why can't the following window appear when editing EB500 software, and it is blank? ...

1. When turning on and off the power of the machine, it should be operated in strict accordance with the regulations; 2. According to the severity of the environment, set a time limit to open the machine head to clean the reflective stripes and inner surface of the touch screen; 3. At present, the mainstream industrial display program does not have a mouse cursor, because the flashing of the cursor will ...

Some tips for using the contact screen If you change the display resolution or display form of the contact screen from scratch when you operate the capacitive contact screen in the middle of the operation, or you may adjust the refresh rate of the contact screen controller by yourself, and you feel that the cursor and the contact point do not correspond, you must ...

1. Omron NJ controller programming 1. The structure data type required for the new project, such as the Boolean switch to be used in this example to create a structure data type of "take-up machine IO", and the integer data used in this example to create a "take-up machine".

Touch screens are mostly placed in public places, and due to the environment, human operation and other reasons, there are often some problems in the use process, as follows. 1. There is no response to the touch after using it for a period of time (1) In the process of long-term use of capacitive screen equipment, the screen and the inside ...

Weiluntong contact screen repair 　　The first step in troubleshooting a touchscreen system is to determine if the problem is related to the display, software, or hardware: Don't confuse the visibility issue with the contact screen issue, the two are unrelated. Software problems are caused by fundamental hardware functions ...

1. High stability, not affected by time and environmental changes 2. Strong adaptability, not subject to current, voltage and static interference, suitable for some harsh environmental conditions (explosion-proof, dust-proof) 3. High light transmittance, no intermediate medium, up to 100% 4. Screen and ...

25. Bit status switch switch, bit status indicator, equipment linkage: Through the bit state switching switch element OFF->ON, the macro command is executed: the bit status indicator is set to the ON state; Select the execution macro through the PLC control, select the trigger mode ON->OFF, and set the bit ...

1. Locate the relevant property. In the property settings of the touch screen, find the properties that need to be set, such as touch screen input, output, communication and other related attributes. 2. Set the properties. Set the appropriate property values as needed. If some properties don't have predefined options, ...

1. Touch failure; 2. Touch the glass plate is broken; 3. The key is damaged and the key is not effective; 4. White vertical bars, horizontal bars, and bright lines appear; 5. Half can be touched, half can not be touched; 6. Can't enter the program; 7. The touch screen cannot be calibrated.

1. The power cord is not properly connected This may seem obvious, but make sure the power cord is connected to the back of the touchscreen and plugged into a power outlet. If it looks like it's connected correctly, disconnect and reconnect both ends of the power cord to make sure the cable isn't loose. 2. The power cord is damaged ...

Question 1, How to solve the problem of double click is not sensitive? Open the infrared touch screen to adjust the sensitivity of the program and reduce the sensitivity. Question 2, Is there any drift phenomenon in the infrared screen? The structure of the infrared touch screen is generated by infrared rays, so usually the sleeves and so on touch the infrared screen ...

1. Plug in the U disk on the touch screen, you don't need to power off the screen, the screen supports the hot-swap function, but at this time, it is best not to communicate with external devices to reduce unnecessary impact. When the screen detects an external device, a dialog box will pop up, select the second Upload Project.